Time-division multiplexing (TDM) is a method of transmitting and receiving independent signals over a common signal path by means of synchronized switches at each end of the transmission line so that each signal appears on the line only a fraction of time according to agreed rules, e.g. with each transmitter working in turn. It can be used when the bit rate of the transmission medium exceeds that of the signal to be transmitted. This form of signal multiplexing was developed in telecommunications for telegraphy systems in the late 19th century but found its most common application in digital telephony in the second half of the 20th century.
Time-division multiplexing was first developed for applications in telegraphy to route multiple transmissions simultaneously over a single transmission line. In the 1870s, Émile Baudot developed a time-multiplexing system of multiple Hughes telegraph machines.
In 1944, the British Army used the Wireless Set No. 10 to multiplex 10 telephone conversations over a microwave relay as far as 50 miles. This allowed commanders in the field to keep in contact with the staff in England across the English Channel.[1]
In 1953, a 24-channel time-division multiplexer was placed in commercial operation by RCA Communications to send audio information between RCA's facility on Broad Street, New York, their transmitting station at Rocky Point and the receiving station at Riverhead, Long Island, New York. The communication was by a microwave system throughout Long Island. The experimental TDM system was developed by RCA Laboratories between 1950 and 1953.
In 1962, engineers from Bell Labs developed the first D1 channel banks, which combined 24 digitized voice calls over a four-wire copper trunk line between Bell central office analogue switches. A channel bank at each end of the line allowed the single line to carry short portions, each of a second, of up to 24 voice calls, in turn. The discrete signals on the trunk line carried 1.544 Mbit/s divided into separate frames per second, each composed of 24 contiguous octets and one framing bit. Each octet in a frame carried a single telephone call in turn. Thus each of 24 voice calls was encoded into two constant-bit-rate streams of 64 kbit/s (one in each direction), and converted back to conventional analog signals by the complementary equipment on the receiving end of the trunk line.[2]
Time-division multiplexing is used primarily for digital signals but may be applied in analog multiplexing, as above, in which two or more signals or bit streams are transferred appearing simultaneously as sub-channels in one communication channel, but are physically taking turns on the channel.[3] The time domain is divided into several recurrent time slots of fixed length, one for each sub-channel. A sample byte or data block of sub-channel 1 is transmitted during time slot 1, sub-channel 2 during time slot 2, etc. One TDM frame consists of one time slot per sub-channel, and usually a synchronization channel and sometimes an error correction channel. After all of these the cycle starts again with a new frame, starting with the second sample, byte or data block from sub-channel 1, etc.
TDM can be further extended into the time-division multiple access (TDMA) scheme, where several stations connected to the same physical medium, for example sharing the same frequency channel, can communicate. Application examples include:
In circuit-switched networks, such as the public switched telephone network (PSTN), it is desirable to transmit multiple subscriber calls over the same transmission medium to effectively utilize the bandwidth of the medium.[4] TDM allows transmitting and receiving telephone switches to create channels (tributaries) within a transmission stream. A standard DS0 voice signal has a data bit rate of 64 kbit/s.[5] A TDM circuit runs at a much higher signal bandwidth, permitting the bandwidth to be divided into time frames (time slots) for each voice signal which is multiplexed onto the line by the transmitter. If the TDM frame consists of n voice frames, the line bandwidth is n*64 kbit/s.
Each voice time slot in the TDM frame is called a channel. In European systems, standard TDM frames contain 30 digital voice channels (E1), and in American systems (T1), they contain 24 channels. Both standards also contain extra bits (or bit time slots) for signaling and synchronization bits.
Multiplexing more than 24 or 30 digital voice channels is called higher order multiplexing. Higher order multiplexing is accomplished by multiplexing the standard TDM frames. For example, a European 120 channel TDM frame is formed by multiplexing four standard 30 channel TDM frames. At each higher order multiplex, four TDM frames from the immediate lower order are combined, creating multiplexes with a bandwidth of n*64 kbit/s, where n = 120, 480, 1920, etc.
There are three types of synchronous TDM: T1, SONET/SDH, and ISDN.[6]
Plesiochronous digital hierarchy (PDH) was developed as a standard for multiplexing higher order frames. PDH created larger numbers of channels by multiplexing the standard Europeans 30 channel TDM frames. This solution worked for a while; however PDH suffered from several inherent drawbacks which ultimately resulted in the development of the Synchronous Digital Hierarchy (SDH). The requirements which drove the development of SDH were these:
SDH has become the primary transmission protocol in most PSTN networks. It was developed to allow streams 1.544 Mbit/s and above to be multiplexed, in order to create larger SDH frames known as Synchronous Transport Modules (STM). The STM-1 frame consists of smaller streams that are multiplexed to create a 155.52 Mbit/s frame. SDH can also multiplex packet based frames e.g. Ethernet, PPP and ATM.
While SDH is considered to be a transmission protocol (Layer 1 in the OSI Reference Model), it also performs some switching functions, as stated in the third bullet point requirement listed above. The most common SDH Networking functions are these:
SDH network functions are connected using high-speed optic fibre. Optic fibre uses light pulses to transmit data and is therefore extremely fast. Modern optic fibre transmission makes use of wavelength-division multiplexing (WDM) where signals transmitted across the fibre are transmitted at different wavelengths, creating additional channels for transmission. This increases the speed and capacity of the link, which in turn reduces both unit and total costs.
See main article: Statistical time-division multiplexing. Statistical time-division multiplexing (STDM) is an advanced version of TDM in which both the address of the terminal and the data itself are transmitted together for better routing. Using STDM allows bandwidth to be split over one line. Many college and corporate campuses use this type of TDM to distribute bandwidth.
On a 10-Mbit line entering a network, STDM can be used to provide 178 terminals with a dedicated 56k connection (178 * 56k = 9.96 Mb). A more common use however is to only grant the bandwidth when that much is needed. STDM does not reserve a time slot for each terminal, rather it assigns a slot when the terminal is requiring data to be sent or received.
In its primary form, TDM is used for circuit mode communication with a fixed number of channels and constant bandwidth per channel. Bandwidth reservation distinguishes time-division multiplexing from statistical multiplexing such as statistical time-division multiplexing. In pure TDM, the time slots are recurrent in a fixed order and pre-allocated to the channels, rather than scheduled on a packet-by-packet basis.
In dynamic TDMA, a scheduling algorithm dynamically reserves a variable number of time slots in each frame to variable bit-rate data streams, based on the traffic demand of each data stream.[7] Dynamic TDMA is used in:
Asynchronous time-division multiplexing (ATDM), is an alternative nomenclature in which STDM designates synchronous time-division multiplexing, the older method that uses fixed time slots.