In telecommunications, a scrambler is a device that transposes or inverts signals or otherwise encodes a message at the sender's side to make the message unintelligible at a receiver not equipped with an appropriately set descrambling device. Whereas encryption usually refers to operations carried out in the digital domain, scrambling usually refers to operations carried out in the analog domain. Scrambling is accomplished by the addition of components to the original signal or the changing of some important component of the original signal in order to make extraction of the original signal difficult. Examples of the latter might include removing or changing vertical or horizontal sync pulses in television signals; televisions will not be able to display a picture from such a signal. Some modern scramblers are actually encryption devices, the name remaining due to the similarities in use, as opposed to internal operation.
In telecommunications and recording, a scrambler (also referred to as a randomizer) is a device that manipulates a data stream before transmitting. The manipulations are reversed by a descrambler at the receiving side. Scrambling is widely used in satellite, radio relay communications and PSTN modems. A scrambler can be placed just before a FEC coder, or it can be placed after the FEC, just before the modulation or line code. A scrambler in this context has nothing to do with encrypting, as the intent is not to render the message unintelligible, but to give the transmitted data useful engineering properties.
A scrambler replaces sequences (referred to as whitening sequences) with other sequences without removing undesirable sequences, and as a result it changes the probability of occurrence of vexatious sequences. Clearly it is not foolproof as there are input sequences that yield all-zeros, all-ones, or other undesirable periodic output sequences. A scrambler is therefore not a good substitute for a line code, which, through a coding step, removes unwanted sequences.
A scrambler (or randomizer) can be either:
There are two main reasons why scrambling is used:
Scramblers are essential components of physical layer system standards besides interleaved coding and modulation. They are usually defined based on linear-feedback shift registers (LFSRs) due to their good statistical properties and ease of implementation in hardware.
It is common for physical layer standards bodies to refer to lower-layer (physical layer and link layer) encryption as scrambling as well.[1] [2] This may well be because (traditional) mechanisms employed are based on feedback shift registers as well.
Some standards for digital television, such as DVB-CA and MPE, refer to encryption at the link layer as scrambling.
Additive scramblers (they are also referred to as synchronous) transform the input data stream by applying a pseudo-random binary sequence (PRBS) (by modulo-two addition). Sometimes a pre-calculated PRBS stored in the read-only memory is used, but more often it is generated by a linear-feedback shift register (LFSR).
In order to assure a synchronous operation of the transmitting and receiving LFSR (that is, scrambler and descrambler), a sync-word must be used.
A sync-word is a pattern that is placed in the data stream through equal intervals (that is, in each frame). A receiver searches for a few sync-words in adjacent frames and hence determines the place when its LFSR must be reloaded with a pre-defined initial state.
The additive descrambler is just the same device as the additive scrambler.
Additive scrambler/descrambler is defined by the polynomial of its LFSR (for the scrambler on the picture above, it is
1+z-14+z-15
Multiplicative scramblers (also known as feed-through) are called so because they perform a multiplication of the input signal by the scrambler's transfer function in Z-space. They are discrete linear time-invariant systems.A multiplicative scrambler is recursive, and a multiplicative descrambler is non-recursive. Unlike additive scramblers, multiplicative scramblers do not need the frame synchronization, that is why they are also called self-synchronizing. Multiplicative scrambler/descrambler is defined similarly by a polynomial (for the scrambler on the picture it is
1+z-18+z-23
Scramblers have certain drawbacks:
The first voice scramblers were invented at Bell Labs in the period just before World War II. These sets consisted of electronics that could mix two signals or alternatively "subtract" one signal back out again. The two signals were provided by a telephone and a record player. A matching pair of records was produced, each containing the same recording of noise. The recording was played into the telephone, and the mixed signal was sent over the wire. The noise was then subtracted out at the far end using the matching record, leaving the original voice signal intact. Eavesdroppers would hear only the noisy signal, unable to understand the voice.
One of those, used (among other duties) for telephone conversations between Winston Churchill and Franklin D. Roosevelt was intercepted and unscrambled by the Germans. At least one German engineer had worked at Bell Labs before the war and came up with a way to break them. Later versions were sufficiently different that the German team was unable to unscramble them. Early versions were known as "A-3" (from AT&T Corporation). An unrelated device called SIGSALY was used for higher-level voice communications.
The noise was provided on large shellac phonograph records made in pairs, shipped as needed, and destroyed after use. This worked, but was enormously awkward. Just achieving synchronization of the two records proved difficult. Post-war electronics made such systems much easier to work with by creating pseudo-random noise based on a short input tone. In use, the caller would play a tone into the phone, and both scrambler units would then listen to the signal and synchronize to it. This provided limited security, however, as any listener with a basic knowledge of the electronic circuitry could often produce a machine of similar-enough settings to break into the communications.
It was the need to synchronize the scramblers that suggested to James H. Ellis the idea for non-secret encryption, which ultimately led to the invention of both the RSA encryption algorithm and Diffie–Hellman key exchange well before either was reinvented publicly by Rivest, Shamir, and Adleman, or by Diffie and Hellman.
The latest scramblers are not scramblers in the truest sense of the word, but rather digitizers combined with encryption machines. In these systems the original signal is first converted into digital form, and then the digital data is encrypted and sent. Using modern public-key systems, these "scramblers" are much more secure than their earlier analog counterparts. Only these types of systems are considered secure enough for sensitive data.
Voice inversion scrambling can be as simple as inverting the frequency bands around a static point to various complex methods of changing the inversion point randomly and in real time and using multiple bands.
The "scramblers" used in cable television are designed to prevent casual signal theft, not to provide any real security. Early versions of these devices simply "inverted" one important component of the TV signal, re-inverting it at the client end for display. Later devices were only slightly more complex, filtering out that component entirely and then adding it by examining other portions of the signal. In both cases the circuitry could be easily built by any reasonably knowledgeable hobbyist. (see Television encryption.)
Electronic kits for scrambling and descrambling are available from hobbyist suppliers. Scanner enthusiasts often use them to listen in to scrambled communications at car races and some public-service transmissions. It is also common in FRS radios. This is an easy way to learn about scrambling.
The term "scrambling" is sometimes incorrectly used when jamming is meant.
See also: Cable television piracy. Descramble in cable television context is the act of taking a scrambled or encrypted video signal that has been provided by a cable television company for premium television services, processed by a scrambler and then supplied over a coaxial cable and delivered to the household where a set-top box reprocesses the signal, thus descrambling it and making it available for viewing on the television set. A descrambler is a device that restores the picture and sound of a scrambled channel. A descrambler must be used with a cable converter box to be able to unencrypt all of the premium & pay-per-view channels of a Cable Television System.