The Program Segment Prefix (PSP) is a data structure used in DOS systems to store the state of a program. It resembles the Zero Page in the CP/M operating system. The PSP has the following structure:
| Offset | Size | Contents | |
|---|---|---|---|
| 00h–01h | 2 bytes (code) | CP/M-80-like | --> exit (always contains INT 20h) |
| 02h–03h | word (2 bytes) | Segment of the first byte beyond the memory allocated to the program | |
| 04h | byte | Reserved | |
| 05h–09h | 5 bytes (code) | CP/M-80-like | --> far call entry into DOS, and program segment size |
| 0Ah–0Dh | dword (4 bytes) | Terminate address of previous program (old INT 22h) | |
| 0Eh–11h | dword | Break address of previous program (old INT 23h) | |
| 12h–15h | dword | Critical error address of previous program (old INT 24h) | |
| 16h–17h | word | Parent's PSP segment (usually COMMAND.COM - internal) | |
| 18h–2Bh | 20 bytes | Job File Table (JFT) (internal) | |
| 2Ch–2Dh | word | Environment segment | |
| 2Eh–31h | dword | SS:SP on entry to last INT 21h call (internal) | |
| 32h–33h | word | JFT size (internal) | |
| 34h–37h | dword | Pointer to JFT (internal) | |
| 38h–3Bh | dword | Pointer to previous PSP (only used by SHARE in DOS 3.3 and later) | |
| 3Ch–3Fh | 4 bytes | Reserved | |
| 40h–41h | word | DOS version to return (DOS 5 and later, alterable via SETVER in DOS 5 and later) | |
| 42h–4Fh | 14 bytes | Reserved | |
| 50h–52h | 3 bytes (code) | Unix-like far call entry into DOS (always contains INT 21h + RETF) | |
| 53h–54h | 2 bytes | Reserved | |
| 55h–5Bh | 7 bytes | Reserved (can be used to make first FCB into an extended FCB) | |
| 5Ch–6Bh | 16 bytes | Unopened Standard FCB 1 | |
| 6Ch–7Fh | 20 bytes | Unopened Standard FCB 2 (overwritten if FCB 1 is opened) | |
| 80h | 1 byte | Number of bytes on command-line | |
| 81h–FFh | 127 bytes | Command-line tail (terminated by a 0Dh) |
The PSP is most often used to get the command line arguments of a DOS program; for example, the command "FOO.EXE /A /F" executes FOO.EXE with the arguments '/A' and '/F'.
If the PSP entry for the command line length is non-zero and the pointer to the environment segment is neither 0000h nor FFFFh, programs should first try to retrieve the command line from the environment variable %CMDLINE% before extracting it from the PSP. This way, it is possible to pass command lines longer than 126 characters to applications.
The segment address of the PSP is passed in the DS register when the program is executed. It can also be determined later by using Int 21h function 51h or Int 21h function 62h. Either function will return the PSP address in register BX.
Alternatively, in .COM programs loaded at offset 100h, one can address the PSP directly just by using the offsets listed above. Offset 000h points to the beginning of the PSP, 0FFh points to the end, etc.
For example, the following code displays the command line arguments:
mov byte [bx+81h],'$'
exit:mov ax,4C00h ; subfunction 4Cint 21h
In DOS 1.x, it was necessary for the CS (Code Segment) register to contain the same segment as the PSP at program termination, thus standard programming practice involved saving the DS register (since the DS register is loaded with the PSP segment) along with a zero word to the stack at program start and terminating the program with a RETF instruction, which would pop the saved segment value off the stack and jump to address 0 of the PSP, which contained an INT 20h instruction.
retf
If the executable was a .COM file, this procedure was unnecessary and the program could be terminated merely with a direct INT 20h instruction or else calling INT 21h function 0. However, the programmer still had to ensure that the CS register contained the segment address of the PSP at program termination. Thus,
mess1 db 'Hello world!$'
start:mov dx,mess1mov ah,9int 21h
int 20h
In DOS 2.x and higher, program termination was accomplished instead with INT 21h function 4Ch which did not require the CS register to contain the segment value of the PSP.