Power factor (PF) in practical shooting competitions refers to a ranking system used to reward cartridges with more recoil. Power factor is a measure of the momentum of the bullet (scaled product of the bullet's mass and velocity), which to some degree reflects the recoil impulse from the firearm onto the shooter (see section on limitations).
Power factor is used in competitions sanctioned by the International Practical Shooting Confederation (IPSC), United States Practical Shooting Association (USPSA), Bianchi Cup, Steel Challenge and International Defensive Pistol Association (IDPA).
The PF is based on the bullet's momentum as it is moving through the air by measuring the bullet speed using a chronograph and measuring a similar bullet mass on a weighing scale, thereafter calculating the power factor by the formula:
{power factor}={mass} ⋅ {velocity}
The PF can be represented using different units:
newton-second=
| gram{ ⋅ m/s | |
kgr{ ⋅ ft/s}=
| gr{ ⋅ ft/s | |
Alternative English Engineering units are slug foot per second (slug⋅ft/s) or pound force seconds (lbf⋅s).
1 kgr{ ⋅ ft/s}=0.019750707768 N{ ⋅ s}.
For example:
1N{ ⋅ s}=
| 1 | |
| 0.019750707768 |
kgr{ ⋅ ft/s}\simeq50.6310987 kgr{ ⋅ ft/s}.
For example:
The table below are examples, and for the same caliber different bullet weights can be used. Bullet velocity depends, along with other factors, on bullet weight, powder types used and barrel length for the particular firearm. Some cartridges not suitable for competition are included for reference.
| Cartridge | Bullet mass (grains) | Muzzle velocity (ft/s) | Power factor (kgr·ft/s) | Bullet mass (gram) | Muzzle velocity (m/s) | Power factor (newton seconds) |
|---|---|---|---|---|---|---|
| .22 Long Rifle (5.6×15mmR) | 40 gr | 1080 ft/s | 43 kgr·ft/s | 2.60 g | 330 m/s | 0.86 N⋅s |
| .30 Carbine (7.62×33mm) | 110 gr | 1920 ft/s | 211 kgr·ft/s | 7.10 g | 585 m/s | 4.16 N⋅s |
| .380 ACP (9×17mm) | 95 gr | 955 ft/s | 91 kgr·ft/s | 6.20 g | 291 m/s | 1.80 N⋅s |
| 9×18mm Makarov | 93 gr | 978 ft/s | 91 kgr·ft/s | 6.00 g | 298 m/s | 1.79 N⋅s |
| 9×19mm | 116 gr | 1150 ft/s | 133 kgr·ft/s | 7.50 g | 350 m/s | 2.63 N⋅s |
| .38 Special (9×29mmR) | 158 gr | 950 ft/s | 150 kgr·ft/s | 10.20 g | 290 m/s | 2.96 N⋅s |
| 9×19mm +P | 124 gr | 1250 ft/s | 155 kgr·ft/s | 8.00 g | 381 m/s | 3.05 N⋅s |
| .38 Special +P (9×29mmR) | 158 gr | 1000 ft/s | 158 kgr·ft/s | 10.20 g | 300 m/s | 3.06 N⋅s |
| .38 Special +P+ (9×29mmR) | 158 gr | 1150 ft/s | 183 kgr·ft/s | 10.20 g | 351 m/s | 3.58 N⋅s |
| .38 Super (9×23mmSR) | 130 gr | 1280 ft/s | 166 kgr·ft/s | 8.40 g | 390 m/s | 3.28 N⋅s |
| .357 SIG (9×22mm) | 125 gr | 1430 ft/s | 179 kgr·ft/s | 8.10 g | 436 m/s | 3.53 N⋅s |
| .357 Magnum (9×33mmR) | 158 gr | 1450 ft/s | 229 kgr·ft/s | 10.20 g | 440 m/s | 4.49 N⋅s |
| .40 S&W (10×22mm) | 155 gr | 1200 ft/s | 186 kgr·ft/s | 10.20 g | 366 m/s | 3.73 N⋅s |
| 10mm Auto (10×25mm) | 220 gr | 1250 ft/s | 275 kgr·ft/s | 14.30 g | 381 m/s | 5.45 N⋅s |
| .41 Remington Magnum +P+ (10.4×33mmR) | 265 gr | 1490 ft/s | 395 kgr·ft/s | 17.20 g | 454 m/s | 7.81 N⋅s |
| .44 Remington Magnum +P+ (10.9×33mmR) | 340 gr | 1470 ft/s | 500 kgr·ft/s | 22.10 g | 448 m/s | 9.90 N⋅s |
| .45 ACP (11.43×23mm) | 230 gr | 850 ft/s | 195 kgr·ft/s | 14.90 g | 260 m/s | 3.87 N⋅s |
| 5.45×39mm | 56 gr | 2887 ft/s | 162 kgr·ft/s | 3.60 g | 880 m/s | 3.17 N⋅s |
| 5.56×45mm NATO | 62 gr | 3100 ft/s | 192 kgr·ft/s | 4.00 g | 945 m/s | 3.78 N⋅s |
| 6.5mm Creedmoor (6.5×48mm) | 129 gr | 2940 ft/s | 379 kgr·ft/s | 8.40 g | 896 m/s | 7.53 N⋅s |
| .300 AAC Blackout (7.62×35mm) | 125 gr | 2215 ft/s | 277 kgr·ft/s | 8.00 g | 675 m/s | 5.40 N⋅s |
| 7.62×39mm | 122 gr | 2356 ft/s | 287 kgr·ft/s | 7.90 g | 718 m/s | 5.67 N⋅s |
| 7.62×51mm NATO | 175 gr | 2590 ft/s | 453 kgr·ft/s | 11.00 g | 790 m/s | 8.69 N⋅s |
| .308 Winchester (7.62×51mm) | 175 gr | 2645 ft/s | 463 kgr·ft/s | 11.00 g | 810 m/s | 8.91 N⋅s |
| .30-06 (7.62×63mm) | 180 gr | 2900 ft/s | 522 kgr·ft/s | 11.70 g | 884 m/s | 10.34 N⋅s |
| 12 gauge-70 mm | 492 gr (1 oz) | 1200 ft/s | 591 kgr·ft/s | 32.00 g | 366 m/s | 11.71 N⋅s |
| 12.7×99mm NATO (.50 BMG) | 750 gr | 2820 ft/s | 2115 kgr·ft/s | 50.00 g | 860 m/s | 43.00 N⋅s |
| .950 JDJ (24.1×70mm) | 2400 gr | 2100 ft/s | 5040 kgr·ft/s | 160.00 g | 640 m/s | 102.40 N⋅s |
For all major practical shooting competitions, claimed power factors are checked by firing the competitor's gun and ammunition through a chronograph. The most common practice is for a competitor to provide a certain number of rounds to the Range/ Safety Officers at the beginning of the match day. During the course of the match, the Range/Safety Officers at the chronograph station will pull a bullet from the competitor's ammunition and weigh it. When the competitor arrives at the chronograph station, they provide their pistol and an empty magazine to the Range/Safety Officer who loads a number of rounds into the magazine and fires them through the chronograph to determine the ammunition's velocity. The power factor is verified against the competitor's claimed power factor. If a competitor claims major power factor and fails to achieve it, they are moved to minor and their targets are scored accordingly. If a competitor fails to make minor power factor, they generally can continue to shoot the match, but will do so for no score.
At local (often referred to as "club") matches, it is rare to verify the competitors' claimed power factor, except to ensure the minimum caliber is met (e.g., an IPSC Standard shooter using a 9 mm bullet and claiming Major power factor).
Measuring the power factor is a quick and easy way to measure recoil, but has some drawbacks. While the power factor measures the momentum of the fired bullet, it doesn't take into consideration the firearm weight or the contribution from the ejected propellant gases which together makes up for the total recoil impulse from the firearm. The contribution from propellant gases depends on the amount of gunpowder and the effectiveness of any muzzle brake or suppressor. The power factor also doesn't take into consideration any angular momentum or torque, i.e. any lever arm caused by an offset between the bore axis of the firearm to the contact point on the shooter. Also, recoil can alternatively be measured by recoil velocity or recoil energy instead of by recoil impulse.
An alternative formula for simplified recoil measurement which also takes into account firearm weight, gun powder weight and the velocity of the gun powder gases has been suggested:[6]
recoilimpulse=
| (bulletweight×bulletvelocity)+(powderweight×powdervelocity) | |
| firearmweight |
Gunpowder velocity depends on the amount and type of powder (burn rate) etc. Assuming that the average velocity of the powder gases is half the bullet muzzle velocity, the formula can be simplified to the following:
recoilimpulse=
| (bulletweight+halfthepowderweight)×bulletvelocity | |
| firearmweight |
IPSC provides the two power factors minor and major, which have different scoring points on paper targets. The IPSC target has the three scoring zones; A, C, and D, with the points 5-3-1 for minor and 5-4-2 for major. Good hits are scored equally regardless of power factor, while lesser hits are penalized less with major power factor. The concept historically originates from the idea that a lesser hit with a harder hitting caliber will be more likely to end a firefight in a real life situation. However, modern ballistic studies have shown no noticeable difference in terminal performance correlating to the recoil difference between typical minor and major handgun calibers.[7] On the other hand, the power factor requirement has been kept to award the greater challenge of marksmanship required by competitors to shoot firearms with more recoil well.
In IPSC competitions all handguns must have a power factor of at least 125 kgr·ft/s (≈ 2.47 newton seconds), and therefore almost anything of 9×19mm or greater caliber will meet the minimum required power factor. The minimum power factor rule is designed to mitigate the speed and accuracy advantages of smaller calibers. Less-powerful cartridges have less recoil, and therefore can be fired more quickly with the same accuracy. Setting a minimum power factor value requires recoil management skills by all competitors.
| Division | Minor scoring | Major scoring |
|---|---|---|
| Handgun Production | 125 kgr·ft/s (≈ 2.47 N⋅s) Only minor scoring | |
| Handgun Standard, classic, revolver | 125 kgr·ft/s (≈ 2.47 N⋅s) | 170 kgr·ft/s (≈ 3.36 N⋅s) |
| Handgun Open | 125 kgr·ft/s (≈ 2.47 N⋅s) | 160 kgr·ft/s (≈ 3.16 N⋅s) |
| Rifle All divisions | 150 kgr·ft/s (≈ 2.96 N⋅s) | 320 kgr·ft/s (≈ 6.32 N⋅s) |
| Shotgun All divisions | 480 kgr·ft/s (≈ 9.48 N⋅s) Only major scoring | |
The desire to get the benefit of major scoring has led to some competitors adopting high speed 9 mm cartridges loaded to major, such as .38 Super. The felt recoil of a normal handgun in .38 Super is similar to the .45 ACP, but the higher pressure in the .38 Super provides more gas pressure for muzzle brakes. The .38 Super caliber became popular in the early 1980s, and has continued to be popular in the open division after its introduction in the 1993 season.
In both the open and standard rifle divisions, minor power factor is dominating due to less recoil, and 5.56×45mm/ .223 Rem is a common caliber. Ammunition loaded to major power factor such as 7.62×51 mm/ .308 Win has a bigger recoil impulse, and is regarded as having an advantage on stages with targets at long range.
In shotgun only a major power factor of 480 kgr·ft/s is used throughout all divisions. 12 gauge is the most common caliber, and most handle the recoil well. The extra power of a 12 gauge gives the competitors better margins of error when it comes to hit steel targets. Although 12 gauge is most prevalent for both male and female shooters, it is also possible to use other calibers, such as the smaller 16 or 20 gauge. The smallest 20 gauge has the advantage that it is easier to carry and for the shooter to keep balance while shooting, thus making it easier to shoot more accurately. However the smaller caliber requires more precision, especially on small steel targets.
USPSA also provide minor and major scoring based on power factor. Metric targets are divided into the scoring areas A, C and D with minor and major points 5-3-3-1 and 5-4-4-2 respectively, while IPSC targets are divided into the scoring areas A, C and D with minor and major points 5-3-1 and 5-4-2 respectively.
In USPSA as of 2014, a value of 165 kgr·ft/s or greater is considered major for all divisions (except production and carry optics where there only is minor scoring), while values below 165 kgr·ft/s are minor.[8] Until a point in the late 1990s, the cut off point for "making major" was 175 kgr·ft/s.
| Division | Minor scoring | Major scoring |
|---|---|---|
| Handgun Production, carry optics | 125 kgr·ft/s (≈ 2.47 N⋅s) Only minor scoring | |
| Handgun Open, limited, limited-10, revolver | 125 kgr·ft/s (≈ 2.47 N⋅s) | 165 kgr·ft/s (≈ 3.26 N⋅s) |
A minimum power factor of 120 kgr·ft/s (≈ 2.37 N⋅s) was previously required to activate the stop plate which stops the competitors time, but since around 2011 the stop plates are no longer connected to timers. Instead regular shot timers that register the last shot fired are used. Therefore, the minimum power factor rule no longer applies, and competitors are encouraged to use low power factor ammo in order to preserve the steel targets.
The IDPA also has different power factors, and they are calculated the same way, however there is no scoring distinction as in USPSA. A particular IDPA division has a minimum power factor, and the firearm/ammunition combination must meet or exceed this minimum to be legal for competition. The minimum power factor was previously set as 125 kgr·ft/s for all divisions, except custom defensive pistol (which is restricted to semiautomatics chambered for .45 ACP), which had a power factor of 165 kgr·ft/s.[9]
In all instances, it is up to the competitor to ensure his or her ammunition meets the requirements for the competition or equipment division.
Effective on 17 January 2011, the power factor for the stock service revolver division (SSR) was reduced to 105 kgr·ft/s since most factory produced .38 special ammunition available on the market did not meet the previous minimum power factor of 125 kgr·ft/s.[10]
To correlate with commonly available ammunition for firearms within a given division, revised power factors were established, effective 1 January 2017.[11]
| IDPA division | Power factor | |
|---|---|---|
| SSP (stock service pistol), ESP (enhanced service pistol), CCP (compact carry pistol) | 125 kgr·ft/s (≈ 2.47 N⋅s) | |
| CDP (custom defense pistol) | 165 kgr·ft/s (≈ 3.26 N⋅s) | |
| Stock Rev | 105 kgr·ft/s (≈ 2.07 N⋅s) | |
| Enhanced rev | 155 kgr·ft/s (≈ 3.06 N⋅s) | |
| BUG (back up gun) | 95 kgr·ft/s (≈ 1.88 N⋅s) |
In the Bianchi Cup, all matches requiring the use of centerfire ammunition must meet or exceed a power factor of 120 kgr·ft/s (≈ 2.37 N⋅s).