South African type XF2 tender explained

South African type XF2 tender
Hatnote:♠ 7½ long tons coal capacity
10 long tons coal capacity
Locomotive:CGR 9th Class of 1906
CGR 10th Class
Designer:Cape Government Railways
(H.M. Beatty)
Builder:Kitson and Company
Date:1906
Wheelarr:2-axle bogies
Length:23feet
Wheeldiameter:NaN0NaN0 as built
340NaN0 retyred
Wheelbase:16feet
Bogie:4feet
Axleload:♠ 9lt
10lt
Bogie 1:♠ 19lt
20lt
Bogie 2:♠ 20lt
21lt
Tenderempty:42128lb
Tenderworking:♠ 39lt
42lt
Fueltype:Coal
Fuelcap:♠ 7lt
101NaN1
Watercap:♠ 3000sigfig=3NaNsigfig=3
Stoking:Manual
Coupling:Drawbar & Johnston link-and-pin
Operator:Cape Government Railways
South African Railways
Fleetnumbers:♠ SAR 948 - SAR 1244

See main article: article and South African steam locomotive tenders.

The South African type XF2 tender was a steam locomotive tender from the pre-Union era in the Cape of Good Hope.

Two Type XF2 tenders entered service in 1906, as tenders to the Mikado type and Mastodon type experimental steam locomotives, of which one each were acquired by the Cape Government Railways in that year. The two tenders were not identical.[1] [2]

Manufacturer

Both Type XF2 tenders were built in 1906 by Kitson and Company.[1] [2]

The tenders entered service as tenders to the CGR 9th Class and CGR 10th Class of 1906, both experimental locomotives. The locomotives and tenders were designed by H.M. Beatty, the Chief Locomotive Superintendent of the Cape Government Railways (CGR), at the Salt River works in Cape Town.[1] [2]

Characteristics

The two tenders were not identical. The tender of the 9th Class had a coal capacity of 7lt and a maximum axle load of 9lt, while the tender of the 10th Class had a coal capacity of 101NaN1 and a maximum axle load of 10lt. Both had a water capacity of 3000sigfig=3NaNsigfig=3.[1] [2]

Locomotives

On the South African Railways (SAR) roster, the two locomotives were designated Classes Experimental 5 and Experimental 6 respectively in 1912. In the SAR years, tenders were numbered for the engines they were delivered with. In most cases, an oval number plate, bearing the engine number and often also the tender type, would be attached to the rear end of the tender. During the classification and renumbering of locomotives onto the SAR roster in 1912, no separate classification and renumbering list was published for tenders, which should have been renumbered according to the locomotive renumbering list.[2] [3]

Only these two experimental locomotives were delivered new with Type XF2 tenders and were renumbered to the SAR numbers as shown.[1] [2] [3]

Classification letters

Since many tender types are interchangeable between different locomotive classes and types, a tender classification system was adopted by the SAR. The first letter of the tender type indicates the classes of engines to which it can be coupled. The "X_" tenders could be used with the following locomotive classes:[2]

The second letter indicates the tender's water capacity. The "_F" tenders had a capacity of 3000impgal.[2]

A number, when added after the letter code, usually indicates differences between similar tender types, such as function, wheelbase or coal bunker capacity.[2]

Notes and References

  1. South African Railways & Harbours/Suid Afrikaanse Spoorweë en Hawens (15 Aug 1941). Locomotive Diagram Book/Lokomotiefdiagramboek, 3'6" Gauge/Spoorwydte. SAR/SAS Mechanical Department/Werktuigkundige Dept. Drawing Office/Tekenkantoor, Pretoria. p. 43.
  2. South African Railways & Harbours/Suid Afrikaanse Spoorweë en Hawens (15 Aug 1941). Locomotive Diagram Book/Lokomotiefdiagramboek, 2'0" & 3'6" Gauge/Spoorwydte, Steam Locomotives/Stoomlokomotiewe. SAR/SAS Mechanical Department/Werktuigkundige Dept. Drawing Office/Tekenkantoor, Pretoria. pp. 6a-7a, 43.
  3. Classification of S.A.R. Engines with Renumbering Lists, issued by the Chief Mechanical Engineer’s Office, Pretoria, January 1912 (Reprinted in April 1987 by SATS Museum, R.3125-6/9/11-1000)