See also: Colorado Railroad Museum.
| Rio Grande Southern Railroad, Motor No. 2 | |
| Nearest City: | Golden, Colorado |
| Coordinates: | 39.7714°N -105.1933°W |
| Builder: | Odenbaugh, Jack; White, Forest |
| Architecture: | narrow gauge RR motor car |
| Added: | February 14, 1997 |
| Area: | less than one acre |
| Refnum: | 97000049 |
| Designated Other1: | Colorado |
| Designated Other1 Date: | June 12, 1996 |
| Designated Other1 Number: | 5JF.1013.1 |
Rio Grande Southern Railroad (RGS), Motor No. 2 (nicknamed Galloping Goose Number 2) is a gasoline engine-powered narrow gauge railroad motorcar. It was converted on August 12, 1931 from a 1927 Buick Master Six 4-door sedan in a conversion known as a Galloping Goose. The Buick was cut behind the rear doorpost and extended with sheet metal 18inches to form an enlarged passenger compartment. With no functional use, the steering column was removed. The couch from the RGS office become the back seat as it is shown being requisitioned for Goose No. 2 on the statement covering construction.[1] The front axle was removed and replaced with a swiveling, two-axle lightweight railroad truck with 16inches-diameter wheels that carried and guided the front of the Goose. Ahead of the front truck the pilot (cow catcher) is attached to the frame. There were two small pivoted scrapers attached to the rear of the pilot to keep small objects on the track from derailing the lightweight front truck. During the winter season a small snowplow was attached to the front of the pilot.[1]
The rear of the frame was lengthened using junked truck frame parts to carry the enclosed mail, express, and freight compartment. The compartment box is sixteen feet long, seven feet wide, and six foot ten inches high at the sides. It has a four-foot wide double door, approximately centered, on each side for access to the mail, express, and freight compartment. The roof is bowed upward in the center to shed moisture. The compartment was fabricated from 2inchesby2inchesin (byin) wood framing, with 1inchesby2inchesin (byin) wood strips running crossways. This is covered with 22 gauge galvanized sheet steel nailed to the 1inchesx2inchesin (xin) strips.[1] The heating of the freight compartment of Goose No. 2 was noted as being considered in September 1931, soon after completion. Goose No. 2's stove is located in a four foot wide by two foot seven inch area added onto the rear of the compartment in the center. Examination shows that it was added on after the compartment box was built, but probably not too long thereafter, as the earliest photographs found show the addition.[1]
The Goose was originally powered by the engine, clutch and transmission that came with the Buick sedan. These powered the rear swiveling two-axle truck assembly mounted under the rear frame and compartment. The drive shaft powers only the forward axle, which was made from a modified Ford truck rear axle. The rearmost axle is driven by roller chains and sprockets mounted outside of the wheels. The rear truck has twenty-four inch diameter cast wheels.[1] The braking is accomplished by brake shoes between the axles on each truck being pushed against the wheel treads. These are actuated by linkage connecting them to the normal foot pedal and parking brake lever. The foot brake is connected to the front truck and the parking brake lever is connected to the rear truck. Goose No. 2 never received air brakes.[1] The original paint scheme of Goose No. 2 is still an item of much discussion. Examination of the paint layers on the rear compartment exterior shows a shade of green on the bottom layer. It is now a light green, probably a faded Pullman dark green paint. Over that is black paint, and then the aluminum paint that was used after 1935. The body on Goose No. 2 was replaced around 1939 with the body from the San Christobal Railroad Goose No. 1 which was built by the RGS for the San Christobal in 1934. This is a Pierce-Arrow Model 80 body and is longer with larger side windows than that of the Buick body. The rear freight compartment was shortened eight inches to allow for the longer body and avoid altering the frame and drive shafts. This is its current configuration as displayed.[1]
Galloping Goose No. 2 is the only example of this type of narrow gauge rail car designed for combination passenger and freight service, which maintains this as-used configuration in Colorado and thus is significant at a statewide level. The period of significance is 1931-1943, the period during which Goose No. 2 operated regularly as part of the Rio Grande Southern Railroad.[1] Otto Mears incorporated the Rio Grande Southern Railroad in November 1889, as another of his many narrow gauge railroads in the San Juan Mountains of Colorado. Narrow gauge railroads operate on rails spaced 3feet apart as opposed to the 4 feet 8 1/2 inch spacing used by standard gauge railroads. Mears planned to tap the economic riches of the area—lumber, livestock, and mined ores, particularly silver. The area to be serviced stretched west and northwest of Durango to Ridgway, north of Ouray. The area was already well populated and promised a lucrative source of rail revenue.[1] Construction of the RGS started in 1890 from the Denver and Rio Grande Railroad (D&RG) tracks in Durango towards Dolores and from the D&RG tracks in Ridgway toward Telluride and Ophir. The 162.6 mile railroad was finished in late 1891 with the joining of the two ends south of Rico. The year 1892 was a successful and profitable year for the RGS, but financial success was not long lasting.[1]