Pennsylvania Railroad class E2 explained

Pennsylvania Railroad E7s
Powertype:Steam
Builder:Altoona Works, Alco
Whytetype:4-4-2
Builddate:The rebuilding of these locomotives began in 1916
Totalproduction:90
Length:68feet (including 55P58 tender)[1]
Leadingdiameter:36inches
Driverdiameter:80inches
Trailingdiameter:50inches
Weightondrivers:118400lb
Locoweight:171100lb
Tenderweight:89050lb
Fueltype:Coal
Fuelcap:12t
Watercap:5800usgal
Boilerpressure:205psi
Firearea:55.5square feet
Cylindercount:2
Cylindersize:22.5x
Tractiveeffort:27409lbf
Preservedunits:One (No. 7002) preserved, remainder scrapped
Disposition:No. 7002 on display

The Pennsylvania Railroad's class E2, E3, E7 steam locomotives were of the 4-4-2 "Atlantic" passenger type, frequently called light Atlantics after the introduction of the heavier E6 Atlantics. All were similar in size and boiler capacity but differed in firebox type, valves and valve gear and cylinder diameter. Classes E2 and E3 were built simultaneously.

Starting in 1916 a rebuilding program converted ninety class E2a, b, and c to class E7s by replacing slide valves with piston valves and increasing cylinder diameter from 20.5to. Fourteen class E2 were similarly converted to class E7sa. Ninety class E2a,d, E3a,d were converted to class E3sd. These improvements allowed many of the engines to remain in active service into the 1930s.

The sub-classes differed as follows:[2]

ClassFireboxCylinder size ValvesValve gearNumber builtYears built
E2 Radial-stay20 ½” x 26”SlideStephenson881901-02
E2a Belpaire20 ½” x 26”SlideStephenson 931902-05
E2b Belpaire20 ½” x 26”PistonStephenson 701903-04
E2c Belpaire20 ½” x 26”SlideStephenson221903
E2d Belpaire20 ½” x 26”PistonWalschaerts321906-08
E3 Radial-stay22” x 26”SlideStephenson81901-02
E3a Belpaire 22” x 26”SlideStephenson1141903-05
E3d Belpaire22” x 26”PistonWalschaerts561906-10
E7s Belpaire22 ½” x 26”PistonStephenson90 converted from E2a/b/c1916-20
E7sa Radial-stay22 ½” x 26”PistonStephenson14 converted from E21916-20

In the first decade of the twentieth century classes E2 and E3 handled all of the fast passenger trains of the Pennsylvania Railroad. As train weights increased due to the switch to steel passenger cars and more cars per train, the “light” Atlantics were usually doubleheaded. Eventually, as Pacific class K2 and K3 became available, they were relegated to secondary service

Engine #7002

See main article: PRR 7002. This engine was built for the Pennsylvania Railroad in 1902 as Class E2 No. 7002. On the first westward run of the Pennsylvania Special (renamed the Broadway Limited in 1912) in June 1905 the conductor clocked the train over three miles just west of Lima, Ohio in 85 seconds, at a record speed of (the claim is dubious, as the train averaged about from Crestline to Fort Wayne). No. 7002 was rebuilt to class E7sa in August 1916 and scrapped in 1935.

When the PRR was looking for an E7 class locomotive for preservation, they refurbished No. 8063 (an E2a from the PRR) and substituted No. 7002’s engine number and builder’s plate. No. 8063 is a PRR E2a built in 1905. The engine was donated to Railroad Museum of Pennsylvania in 1979 and put into operating order by Strasburg Rail Road where it ran for until December 20, 1989, sometimes doubleheading with PRR D16 No. 1223.

Notes and References

  1. Web site: PRR E2a,E3a Steam Loco . PRR.Railfan.net . Pennsylvania Railroad . January 2, 2008.
  2. Book: Staufer, Alvin F . Edson, D. William . Harley, E. Thomas . Pennsy Power III . 1993 . Staufer Books & Prints . 0-944513-10-7.