A nanocrystalline (NC) material is a polycrystalline material with a crystallite size of only a few nanometers. These materials fill the gap between amorphous materials without any long range order and conventional coarse-grained materials. Definitions vary, but nanocrystalline material is commonly defined as a crystallite (grain) size below 100 nm. Grain sizes from 100 to 500 nm are typically considered "ultrafine" grains.
The grain size of a NC sample can be estimated using x-ray diffraction. In materials with very small grain sizes, the diffraction peaks will be broadened. This broadening can be related to a crystallite size using the Scherrer equation (applicable up to ~50 nm), a Williamson-Hall plot,[1] or more sophisticated methods such as the Warren-Averbach method or computer modeling of the diffraction pattern. The crystallite size can be measured directly using transmission electron microscopy.[1]
Nanocrystalline materials can be prepared in several ways. Methods are typically categorized based on the phase of matter the material transitions through before forming the nanocrystalline final product.
Solid-state processes do not involve melting or evaporating the material and are typically done at relatively low temperatures. Examples of solid state processes include mechanical alloying using a high-energy ball mill and certain types of severe plastic deformation processes.
Nanocrystalline metals can be produced by rapid solidification from the liquid using a process such as melt spinning. This often produces an amorphous metal, which can be transformed into an nanocrystalline metal by annealing above the crystallization temperature.
Thin films of nanocrystalline materials can be produced using vapor deposition processes such as MOCVD.[2]
Some metals, particularly nickel and nickel alloys, can be made into nanocrystalline foils using electrodeposition.[3]
Nanocrystalline materials show exceptional mechanical properties relative to their coarse-grained varieties. Because the volume fraction of grain boundaries in nanocrystalline materials can be as large as 30%,[4] the mechanical properties of nanocrystalline materials are significantly influenced by this amorphous grain boundary phase. For example, the elastic modulus has been shown to decrease by 30% for nanocrystalline metals and more than 50% for nanocrystalline ionic materials.[5] This is because the amorphous grain boundary regions are less dense than the crystalline grains, and thus have a larger volume per atom,
\Omega
U(\Omega)
E\propto\partial2U/\partial\Omega2
The exceptional yield strength of nanocrystalline metals is due to grain boundary strengthening, as grain boundaries are extremely effective at blocking the motion of dislocations. Yielding occurs when the stress due to dislocation pileup at a grain boundary becomes sufficient to activate slip of dislocations in the adjacent grain. This critical stress increases as the grain size decreases, and these physics are empirically captured by the Hall-Petch relationship,
\sigmay=\sigma0+Kd-1/2,
\sigmay
\sigma0
K
d
As the grain size continues to decrease, a critical grain size is reached at which intergranular deformation, i.e. grain boundary sliding, becomes more energetically favorable than intragranular dislocation motion. Below this critical grain size, often referred to as the “reverse” or “inverse” Hall-Petch regime, any further decrease in the grain size weakens the material because an increase in grain boundary area results in increased grain boundary sliding. Chandross & Argibay modeled grain boundary sliding as viscous flow and related the yield strength of the material in this regime to material properties as
\tau=(L
| \rhoL | )(1- | |
| M |
| T | |
| Tm |
)fg,
L
\rhoL/M
Tm
fg
fg=(1-\delta/d)3
\delta
d
Due to the large amount of interfacial energy associated with a large volume fraction of grain boundaries, nanocrystalline metals are thermally unstable. In nanocrystalline samples of low-melting point metals (i.e. aluminum, tin, and lead), the grain size of the samples was observed to double from 10 to 20 nm after 24 hours of exposure to ambient temperatures. Although materials with higher melting points are more stable at room temperatures, consolidating nanocrystalline feedstock into a macroscopic component often requires exposing the material to elevated temperatures for extended periods of time, which will result in coarsening of the nanocrystalline microstructure. Thus, thermally stable nanocrystalline alloys are of considerable engineering interest. Experiments have shown that traditional microstructural stabilization techniques such as grain boundary pinning via solute segregation or increasing solute concentrations have proven successful in some alloy systems, such as Pd-Zr and Ni-W.[7]
While the mechanical behavior of ceramics is often dominated by flaws, i.e. porosity, instead of grain size, grain-size strengthening is also observed in high-density ceramic specimens.[8] Additionally, nanocrystalline ceramics have been shown to sinter more rapidly than bulk ceramics, leading to higher densities and improved mechanical properties, although extended exposure to the high pressures and elevated temperatures required to sinter the part to full density can result in coarsening of the nanostructure.
The large volume fraction of grain boundaries associated with nanocrystalline materials causes interesting behavior in ceramic systems, such as superplasticity in otherwise brittle ceramics. The large volume fraction of grain boundaries allows for a significant diffusional flow of atoms via Coble creep, analogous to the grain boundary sliding deformation mechanism in nanocrystalline metals. Because the diffusional creep rate scales as
d-3
While the synthesis of nanocrystalline feedstocks in the form of foils, powders, and wires is relatively straightforward, the tendency of nanocrystalline feedstocks to coarsen upon extended exposure to elevated temperatures means that low-temperature and rapid densification techniques are necessary to consolidate these feedstocks into bulk components. A variety of techniques show potential in this respect, such as spark plasma sintering[9] or ultrasonic additive manufacturing,[10] although the synthesis of bulk nanocrystalline components on a commercial scale remains untenable.