This is an incomplete list of DIN standards.
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Cone Pins, untempered | Withdrawn | ISO 2339 | |||
Standard measurements | Withdrawn | ||||
Technical drawings – Axonometric projections, Isometric projection | Withdrawn | ISO 5456-1, ISO 5456-2, ISO 5456-3, ISO 5456-4 | |||
Technical drawings – projections, terms | Withdrawn | ISO 10209-2 | |||
Projection displays in Normal, views and special presentations | Withdrawn | ISO 128 | |||
Parallel Pins | Withdrawn | ISO 2338 | |||
Whitworth pipe threads 1/4"-6" Thread diameter, sizes, teaching information | Withdrawn | ||||
ISO general purpose metric screw threads – Part 1: Nominal sizes for coarse pitch threads; nominal diameter from 1 mm to 68 mm | Active | ||||
ISO general purpose metric screw threads – Part 2: Nominal sizes for 0,2 mm, 0,25 mm and 0,35 mm fine pitch threads; nominal diameter from 1 mm to 50 mm | Active | ||||
ISO general purpose metric screw threads – Part 3: Nominal sizes for 0,5 mm fine pitch threads; nominal diameter from 3,5 mm to 90 mm | Active | ||||
ISO general purpose metric screw threads – Part 4: Nominal sizes for 0,75 mm fine pitch threads; nominal diameter from 5 mm to 110 mm | Active | ||||
ISO general purpose metric screw threads – Part 5: Nominal sizes for 1 mm and 1,25 mm fine pitch threads; nominal diameter from 7,5 mm to 200 mm | Active | ||||
ISO general purpose metric screw threads – Part 6: Nominal sizes for 1,5 mm fine pitch threads; nominal diameter from 12 mm to 300 mm | Active | ||||
ISO general purpose metric screw threads – Part 7: Nominal sizes for 2 mm fine pitch threads; nominal diameter from 17 mm to 300 mm | Active | ||||
ISO general purpose metric screw threads – Part 8: Nominal sizes for 3 mm fine pitch threads; nominal diameter from 28 mm to 300 mm | Active | ||||
ISO general purpose metric screw threads – Part 9: Nominal sizes for 4 mm fine pitch threads; nominal diameter from 40 mm to 300 mm | Active | ||||
ISO general purpose metric screw threads – Part 10: Nominal sizes for 6 mm fine pitch threads; nominal diameter from 70 mm to 500 mm | Active | ||||
ISO general purpose metric screw threads – Part 11: Nominal sizes for 8 mm fine pitch threads; nominal diameter from 130 mm to 1000 mm | Active | ||||
ISO general purpose metric screw threads – Part 12: 1 to 300 mm diameter coarse and fine pitch threads Selected diameters and pitches | Active | ||||
ISO general purpose metric screw threads – Part 13: Selected sizes for screws, bolts and nuts from 1 to 52 mm screw thread diameter and limits of sizes | Active | ||||
ISO general purpose metric screw threads – Part 19: Nominal profiles | Active | ||||
ISO general purpose metric screw threads – Part 20: Limits of sizes for coarse pitch threads with the preferred tolerance classes; nominal sizes from 1 mm to 68 mm | Active | ||||
ISO general purpose metric screw threads – Part 21: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 1 mm to 24,5 mm | Active | ||||
ISO general purpose metric screw threads – Part 22: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 25 mm to 52 mm | Active | ||||
ISO general purpose metric screw threads – Part 23: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 53 mm to 110 mm | Active | ||||
ISO general purpose metric screw threads – Part 24: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 112 mm to 180 mm | Active | ||||
ISO general purpose metric screw threads – Part 25: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 182 mm to 250 mm | Active | ||||
ISO general purpose metric screw threads – Part 26: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 252 mm to 1000 mm | Active | ||||
ISO general purpose metric screw threads – Part 28: Coarse and Fine Screw Threads from 1 to 250 mm Screw Thread Diameter; Root Cross-sections, Tensile Stress Cross-sections and Pitch Angles | Active | ||||
ISO general purpose metric screw threads – Part 50: Combination of tolerance classes for formed internal screw threads | Active | ||||
ISO general purpose metric screw threads – Part 51: External screw threads for transition fits (former: screw threads for interference fit); tolerances, limit deviations, limits of sizes | Active | ||||
ISO general purpose metric screw threads – Part 52: Multi-start thread tolerances and deviation of profile | Active | ||||
DIN 15-2 | Technical drawings; lines; general application | Withdrawn | DIN ISO 128-24 | ||
Oblique Standard Typeface for Drawings | Withdrawn | ||||
Upright Standard Typeface for Drawings | Withdrawn | ||||
DIN 38 | Plain bearings; bearing metal lining for thick-walled multilayer plain bearings | Active | |||
DIN 74 | Countersinks for countersunk head screws (except screws with DIN EN 27721 head) | Active | |||
Thread run-outs and thread undercuts for ISO metric threads in accordance with DIN 13-1 | Active | ||||
Thread run-outs and thread undercuts for pipe threads conforming to ISO 228 part 1 | Active | ||||
Runouts, Undercuts for Trapezoidal Threads, Buttress Threads and Knuckle Threads and other Threads of Coarse Pitch | Active | ||||
Protrusions of bolt ends | Active | DIN EN ISO 4753 (governs thread ends for bolts assembled with hexagon slotted nuts) | ISO 4753 | ||
Product grade A slotted cheese head screws | Withdrawn | ISO 1207 | |||
Product grade A slotted pan head screws | Withdrawn | ISO 1580 | |||
Product slotted oval head countersunk machine screws | Withdrawn | ISO 2010-1983[1] | |||
Tab washers with long tab | Withdrawn | ||||
Split pins | Withdrawn | ISO 1234 | |||
Slotted Raised Countersunk (Oval) Head Wood Screws | Active | ||||
Slotted Round Head Wood Screws | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
DIN 101 | Rivets – Technical specifications | Active | |||
ISO Metric Trapezoidal Screw Thread; Profiles | Active | ||||
ISO Metric Trapezoidal Screw Thread; General Plan | Active | ||||
ISO Metric Trapezoidal Screw Thread; Allowances and Tolerances for Trapezoidal Screw Threads of General Purpose | Active | ||||
ISO Metric Trapezoidal Screw Thread; Nominal Dimensions | Active | ||||
ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Nut Threads from 8 to 100 mm Nominal Diameter | Active | ||||
ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Nut Threads from 105 to 300 mm Nominal Diameter | Active | ||||
ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Bolt Threads from 8 to 100 mm Nominal Diameter | Active | ||||
ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Bolt Threads from 105 to 300 mm Nominal Diameter | Active | ||||
ISO metric trapezoidal screw threads; gauging of external and internal threads; gauge dimensions and design features | Active | ||||
Clay masonry units – Part 1: Solid and hollow bricks with density classes of 1,2 | Withdrawn | EN 771-1 | |||
Clay masonry units – Part 2: Solid and hollow bricks with density classes equal 1.0 | Withdrawn | EN 771-1 | |||
Clay masonry units – Part 3: Tile and high strength-high-strength clinker | Withdrawn | EN 771-1 | |||
Clay masonry units – Part 4: Ceramic bricks | Withdrawn | EN 771-1, EN 772-7 | |||
Clay masonry units – Part 5: Lightweight long-hole brick and light long-hole brick panels | Active | ||||
Clay masonry units – Part 6: High precision units | Active | ||||
Clay masonry units – Part 100: Clay masonry units with specific properties | Active | ||||
Washers; medium type, primarily for hexagon bolts | Withdrawn | ISO 7089, ISO 7090 | |||
Product grade A washers – with a hardness up to 250 HV designed for use with hexagon head bolts and nuts | Withdrawn | ISO 7089, ISO 7090 | |||
Product grade A washers – with a hardness up to 300 HV designed for use with hexagon head bolts and nuts | Withdrawn | ISO 7089, ISO 7090 | |||
Product grade C washers – designed for use with hexagon head bolts and nut | Withdrawn | ISO 7091 | |||
Spring lock washers with square ends or tang ends | Withdrawn | ||||
Curved and wave spring lock washers | Withdrawn | ||||
Spring washers, curved or wave | Withdrawn | ||||
DIN 174 | Bright Flat Steel; Dimensions, Permissible Variations, Weights | Withdrawn | DIN EN 10278 | ||
DIN 175 | Polished round steel; Dimensions, Permissible deviations according to ISO tolerance zone h9 | Withdrawn | DIN EN 10278 |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Technical drawings; Hatchings; Representation of cutting edges and materials | Withdrawn | ISO 128-50 | |||
Machine Reamers with Screwed-on Blades | Active | ||||
Fasteners – Part 1: Technical delivery conditions; General requirements | Withdrawn | ISO 8992 | |||
Fasteners – Part 2: Technical delivery conditions; Bolts, Screws, Nuts and Similar Threaded and Formed Parts; Types and Dimensional Accuracy | Active | ISO 4759-1 | |||
Fasteners – Part 3: Technical delivery conditions; Property classes for carbon steel and alloy steel bolts and screws; Conversion of property classes | Withdrawn | ISO 898-1 | |||
Fasteners – Part 4: Technical delivery conditions; Property classes for nuts (previous classes) | Withdrawn | ISO 898-2 | |||
Fasteners – Part 5: Technical delivery conditions; Acceptance inspection; modified version of ISO 3269, 1984 edition | Withdrawn | ISO 3269 | |||
Fasteners – Part 6: Technical delivery conditions; Designs and accuracy of measurement for product grade F | Active | ||||
Fasteners – Part 9: Technical delivery conditions; Bolts made of unalloyed or low-alloy steels | Withdrawn | ISO 898-1 | |||
Fasteners – Part 9: Technical delivery conditions; Components with Electroplated Coatings | Withdrawn | ISO 4042 | |||
Fasteners – Part 10: Technical delivery conditions; Hot dip galvanized parts | Withdrawn | ISO 10684 | |||
Fasteners – Part 11: Technical delivery conditions (with additions to ISO 3506); Corrosion-resistant stainless steel fasteners | Withdrawn | ||||
Fasteners – Part 12: Technical delivery conditions; Self-tapping screws | Withdrawn | ISO 2702 | |||
Fasteners – Part 13: Technical delivery conditions; Components for Bolted Connections Made Mainly from Materials Exhibiting a High Impact Strength at Low Temperature or from Materials with a High Temperature Strength | Active | ||||
Fasteners – Part 15: Technical delivery conditions; Prevailing torque type nuts | Withdrawn | ISO 2320, ISO 3506-1, ISO 3506-2, ISO 3506-3 | |||
Fasteners – Part 18: Technical delivery conditions; Components made of Non-ferrous Metals | Withdrawn | ISO 8839 | |||
Fasteners – Part 19: Technical delivery conditions; Surface discontinuities on bolts and screws | Withdrawn | ISO 6157-1, ISO 6157-3 | |||
Fasteners – Part 20: Technical delivery conditions; Surface discontinuities on nuts | Withdrawn | ISO 6157-2, ISO 10484, ISO 10485 | |||
Fasteners – Part 21: Technical delivery conditions; Widening test on nuts | Withdrawn | ISO 6157-2, ISO 10484, ISO 10485 | |||
Fasteners – Part 23: Technical delivery conditions; Property classes for nuts with fine thread (ISO classes) | Withdrawn | ISO 898-6 | |||
Fasteners – Part 24: Technical delivery conditions; Property classes for nuts (Hardness classes) | Active | ||||
Fasteners – Part 25: Technical delivery conditions; Torsion testing of M1 to M10 bolts and screws | Withdrawn | EN 20898-7 | |||
Fasteners – Part 26: Technical delivery conditions; Conical spring washers for bolt/nut assemblies | Active | ||||
Fasteners – Part 27: Technical specifications; Steel screws, bolts and studs with adhesive coating | Active | ||||
Fasteners – Part 28: Technical specifications; Steel screws, bolts and studs with locking coating | Active | ||||
Fasteners – Part 29: Technical specifications; Product grades for parts for bolted connections for use at temperatures ranging from −200 °C to +700 °C | Withdrawn | ||||
Fasteners – Part 30: Technical specifications; Metric thread rolling screws of property class 10.9 | Active | ||||
Building costs; Part 1: Building construction | Active | ||||
Building costs; Part 2: Classification of cost | Withdrawn | ||||
Building costs; Part 3: Ascertainment of cost | Withdrawn |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Wing nuts with rounded wings | Active | ||||
Wing screws with rounded wings | Active | ||||
Drill drifts for taper shanks with drift tang | Active | ||||
Preferred Numbers and Series of Preferred Numbers; Basic Values, Calculated Values, Rounded Values | Withdrawn | ||||
Preferred Numbers and Series of Preferred Numbers; Introduction | Active | ||||
60° centre holes; types R, A, B, and C | Active | ||||
Center holes 60° with thread for shaft ends for rotating electrical machines | Active | ||||
Centre holes for rail vehicles axles | Active | ||||
Machine tools; 60° centre holes; dimensioning | Active | ||||
Centre holes 90°, form S; dimensions, determination process | Active | ||||
Center Holes; Indications on Technical Drawings | Withdrawn | ISO 6411 | |||
Parallel shank twist drills, jobber series | Active | ||||
Sets of taps – Sets of 3 taps for metric coarse ISO-threads M1 to M68 | Active | ||||
Machine taps with reinforced shank for coarse pitch metric ISO-threads M1 to M10 and fine pitch metric ISO-threads M1 × 0,2 to M10 × 1,25 | Active | ||||
Machine screwing taps for fine pitch metric ISO-threads M3 × 0,2 to M52 × 4 | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Slotted capstan screws | Active | ||||
Engineering drawing practice; dimensioning; concepts and general principles | Active | ||||
Engineering drawing practice; dimensioning; principles of application | Active | ||||
Engineering drawing practice; dimensioning; tolerancing of linear and angular dimensions (modified version of ISO 406:1987) | Active | ||||
Slotted set screws with long dog point | Withdrawn | ISO 7435 | |||
Slotted headless screws with chamfered end | Withdrawn | ISO 2342 | |||
Hexagon nuts, Grade C | Withdrawn | ISO 4034 | |||
Washers for use with cheese head screws | Withdrawn | ISO 7092 | |||
Product grade A washers – with a hardness up to 250 HV designed for use with cheese head screws | Withdrawn | ISO 7092 | |||
Product grade A washers – with a hardness up to 300 HV designed for use with cheese head screws | Withdrawn | ISO 7092 | |||
Slotted set screws with cup point | Withdrawn | ISO 7436 | |||
Hexagon thin nuts | Withdrawn | ISO 4035, ISO 4036, ISO 8675 | |||
Unchamfered hexagon thin nuts – Product grade B | Withdrawn | ISO 4036 | |||
Chamfered hexagon thin nuts – Product grades A and B | Withdrawn | ISO 4035, ISO 8675 | |||
Washers for use in timber constructions | Withdrawn | ISO 7094 | |||
Eyebolts | Active | ||||
Graphical Representation in Systems of Coordinates | Active | ||||
Machine Tools; Internal Tab Washers for Slotted Round Nuts for Hook Spanner according to DIN 1804 | Active | ||||
Knurled thumb screws, high type | Active | ||||
Knurled nuts, high type | Active | ||||
Knurled nuts, low type | Active | ||||
Circlips (retaining rings) for shafts; Normal type and heavy type | Active | ||||
Circlips (retaining rings) for internal grooves; Normal type and heavy type | Active | ||||
Paper sizes | Withdrawn | ISO 216 | |||
Trimmed Sizes of Paper – C Series | Active | ||||
Gas cylinder valves for cylinder test pressures up to 300 bar – Part 1: Valve inlet and outlet connections | Active | ||||
Square head bolts with short dog point | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Metal washers; technical delivery conditions | Withdrawn | ISO 4759-3 | |||
Round nuts with set pin holes in side | Active | ||||
Slotted set screws with flat point | Withdrawn | ISO 4766 | |||
Slotted set screws with cone point | Withdrawn | ISO 7434 | |||
M5 to M100x6 hexagon nuts – Product grade C | Withdrawn | ISO 4034 | |||
Hexagon head screws | Withdrawn | ISO 4018 | |||
Collar eyebolts for lifting purposes | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
M5 to M52 hexagon head bolts; product grade C | Withdrawn | ISO 4016 | |||
Mushroom head square neck bolts | Active | ||||
Hexagon fits bolts with long thread | Active | ||||
Rolling bearings; single row radial contact ball bearings | Active | ||||
Rolling bearings; double row radial contact ball bearings | Active | ||||
Rolling bearings; radial contact groove ball bearings with flanged outer ring | Active | ||||
Knurled thumb screws, low type | Active | ||||
Envelopes – Part 1: Sizes | Active | ||||
Envelopes – Part 2: Envelopes for Processing in Enveloping Machines, Size C6 to C4 | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Tested, non-calibrated, long-link round steel chains | Active | ||||
Calibrated and tested round steel link chains for continuous conveyors; grade 2, pitch 3,5d | Active | ||||
Calibrated and tested round steel link chains for continuous conveyors; grade 3, pitch 3,5d | Active | ||||
Calibrated and tested grade 3 round steel link chains | Active | ||||
Foundation Blocks | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Standards Work – Part 1: Principles | Active | ||||
Standardization – Part 2: Presentation of standards; examples for presentation of figures, tables and part lists | Active | ||||
Standardization – Pdfart 3: Concepts | Active | ||||
Standardization – Part 4: Working procedure | Active | ||||
Standardization – Part 11: Presentation of Standards concerning safety regulations which are VDE-Specifications or VDE-Guidelines | Active | ||||
Standardization – Part 12: Presentation of standards concerning safety regulations | Active | ||||
Standardization – Part 13: Adoption of European documents of CEN, CENELEC and of ETSI; Concepts and presentation | Active | ||||
Standardization – Part 15: Implementation of ISO and IEC international documents; Concepts and presentation | Active | ||||
Standardization – Part 120: Guidelines for the inclusion of safety aspects in standards (ISO/IEC Guide 51:1999) | Active | ||||
Technical drawings; Folding to filing size | Active | ||||
Hand Operated Wrenches and Sockets; Technical Specifications | Withdrawn | ISO 1711-1 |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
internal drive pipe plugs for the sealing of holes with cylindrical internal threads | Active | ||||
Hexagon socket screw plugs with parallel screw thread | Active | ||||
Hexagon-duty hexagon head screw plugs | Active | ||||
Hexagon Socket Screw Keys | Withdrawn | ISO 2936 | |||
Hexagon socket head cap screws (modified version of ISO 4762) | Withdrawn | ISO 4762, ISO 21269 | |||
Hexagon socket set screws with flat point (ISO 4026 modified) | Withdrawn | ISO 4026 | |||
Hexagon socket set screws with cone point (ISO 4027 modified) | Withdrawn | ISO 4027 | |||
Hexagon socket set screws with dog point (ISO 4028 modified) | Withdrawn | ISO 4028 | |||
Hexagon socket set screws with cup point (ISO 4029 modified) | Withdrawn | ISO 4029 | |||
Fasteners; Terminology; Spelling of terms; Abbreviations | Active | ||||
Overview of European Standards for fasteners | Active | ||||
Technical Drawings; Wood Processing; Principles | Active | ||||
Slotted pan head screws with large head | Active | ||||
Slotted pan head screws with shoulder | Active | ||||
Hexagon weld nuts | Active | ||||
Fine thread pitch partially threaded screws | Withdrawn | ||||
M1,6 to M39 Hexagon Cap Screws Partially Threaded – Product grades A and B | Withdrawn | ISO 4014 | |||
M42 to M160x6 Hexagon Cap Screws Partially Threaded – Product grade B | Withdrawn | ISO 4014 | |||
M1,6 to M52 Hexagon Cap Screws Fully Threaded – Product grades 8.8 | Withdrawn | ISO 4017 | |||
Hexagon nuts with metric coarse and fine pitch thread – Product classes A and B | Withdrawn | ISO 4032, ISO 8673 | |||
Hexagon slotted nuts and castle nuts with metric coarse and fine pitch thread – Product grades A and B | Active | ||||
M42 to M160x6 hexagon head nuts; product grade B | Active | ||||
Hexagon slotted nuts with metric coarse pitch thread – Product grade C | Active | ||||
M8 to M52 and M8x1 to M52x3 hexagon thin nuts; product grades A and B | Withdrawn | ||||
Hexagon thin castle nuts | Withdrawn | ||||
Studs with a length of engagement equal to about 1 d | Active | ||||
Studs with a length of engagement equal to about 1,25 d | Active | ||||
Determination of coefficient of friction of bolt/nut assemblies under specified conditions | Withdrawn | ISO 16047 | |||
M8x1 to M100x4 hexagon head bolts with fine pitch thread – Product grades A and B | Withdrawn | ISO 8765, ISO 8676 | |||
M8x1 to M52x3 hexagon head bolts with fine pitch thread – Product grades A and B | Withdrawn | ISO 8676 | |||
Designation system for fasteners | Active | ||||
Slotted countersunk head screws (with countersunk heads as specified in ISO 2009-1972) | Withdrawn | ISO 2009 | |||
Slotted raised countersunk oval head screws | Withdrawn | ISO 2010 | |||
Cross recessed countersunk flat head screws | Withdrawn | ISO 7046-1, ISO 7046-2 | |||
Cross recessed raised countersunk head screws | Withdrawn | ISO 7047 | |||
Hexagon nuts; Style 1; Metric coarse thread, Product grades A and B; ISO 4032 modified | Withdrawn | ISO 4032 | |||
Style 1 hexagon nuts with metric fine pitch thread; property classes 6 and 8 | Withdrawn | ISO 8673 | |||
Style 2 hexagon nuts with metric fine pitch thread; property classes 10 and 12 | Withdrawn | ISO 8674 | |||
M5 to M39 hexagon nuts; style 1; product grade C (modified version of ISO 4034) | Withdrawn | ISO 4034 | |||
Threaded rods | Withdrawn | ||||
Metric thread stud bolts | Active | ||||
Metric interference-fit thread stud bolts | Active | ||||
Hexagon weld nuts with flange | Withdrawn | ISO 21670 | |||
Hexagon thin slotted nuts and castle nuts with metric coarse and fine pitch thread – Product grades A and B | Active | ||||
All-metal prevailing torque type hexagon nuts | Withdrawn | ISO 7042, ISO 10513 | |||
Locknuts for use with rolling bearings | Active | ||||
Prevailing torque type hexagon nuts with nonmetallic insert | Withdrawn | ISO 7040, ISO 10512 | |||
Retaining rings with lugs for use on shafts (external circlips) | Active | ||||
Prevailing torque type hexagon thin nuts with nonmetallic insert | Withdrawn | ISO 10511 | |||
Prevailing torque type hexagon domed cap nuts with non-metallic insert | Active | ||||
Shim rings and supporting rings | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Hot rolled I-sections – Part 1: Narrow flange I-sections, I-serie – Dimensions, masses, sectional properties | Active | ||||
Hot rolled I-beams – Part 2: Wide flange I-beams, IPB-serie; dimensions, masses, sectional properties | Active | ||||
Hot rolled I-beams; wide flange I-beams, light pattern, IPBl-serie; dimensions, masses, sectional properties | Active | ||||
Hot rolled I-beams; wide flange I-beams heavy pattern, IPBv-serie; dimensions, masses, sectional properties | Active | ||||
Hot rolled I-beams; medium flange I-beams, IPE-serie; dimensions, masses, sectional properties | Active | ||||
Units – Part 1: Names and Symbols | Active | ||||
Units – Part 2: Submultiples and Multiples for General Use | Active | ||||
Units – Part 3: Conversions of Units No Longer To Be Used | Active | ||||
General Mathematical Symbols and Concepts | Active | ||||
Vectors, matrices, tensors; symbols and concepts | Active | ||||
Letter symbols for physical quantities – Part 1: Symbols for general use | Active | ||||
Letter symbols for physical quantities – Part 2: Symbols for use in meteorology and geophysics | Active | ||||
Letter symbols for physical quantities – Part 3: Symbols for use in electric power engineering | Active | ||||
Letter symbols for physical quantities – Part 5: Symbols for use in fluid mechanics | Active | ||||
Letter symbols for physical quantities – Part 9: Symbols for use in the field of static converters using semiconductor devices | Active | ||||
Letter symbols for physical quantities – Part 9: Symbols for equivalent circuits of piezoelectric crystals | Active | ||||
(Mechanical) vibrations, oscillations and vibration systems – Part 1: Basic concepts, survey | Active | ||||
(Mechanical) vibrations, oscillations and vibration systems – Part 2: Linear vibration systems with single degree of freedom | Active | ||||
(Mechanical) vibrations, oscillations and vibration systems – Part 3: Linear time-invariant vibration systems with a finite number of degrees of freedom | Active | ||||
Vibration; Vibrating Continua, Waves | Active | ||||
Physical Quantities and Equation; Concepts, Methods of Writing | Active | ||||
Angle; Concepts, Units | Active | ||||
Loudness Level | Active | ||||
Fundamentals of Metrology – Part 1: Basic Terminology | Active | ||||
Basic Concepts in Metrology – Part 2: Terminology Related To Measuring Equipment | Active | ||||
Basic Concepts in Metrology – Part 3: Terminology Relating To the Uncertainty of Measurement and the Assessment of Measuring Instruments and Measuring Equipment | Active | ||||
Basic Concepts in Metrology – Part 4: Treatment of Uncertainties in the Evaluation of Measurements | Active | ||||
Acoustics; Terminology | Active | ||||
Electromagnetic Field – Part 1. State Quantities | Active | ||||
Electromagnetic Field – Part 2. Material Quantities | Active | ||||
Electromagnetic Field – Part 3. Electromagnetic Waves | Active | ||||
Vocabulary for value management, value analysis and functional analysis – Part 1: Value analysis and functional analysis | Active | ||||
Value Management, Value Analysis, Functional Analysis Vocabulary – Part 2: Value Management | Active | ||||
Acoustics; Symbols | Withdrawn | ISO 80000-8 | |||
Presentation of Numerical Data | Active | ||||
Writing and Typesetting of Formulae | Active | ||||
Time; Calendar, Numbering of Weeks, Date of Day, (Clock) Time | Withdrawn | ||||
Arrangement and Numbering in Texts; Clauses, Paragraphs, Enumerations | Active | ||||
Publications in Sciences, Technology, Economy and Administration; Presentation of Manuscripts and Typoscripts | Active | ||||
Publications in Sciences, Technology, Economy and Administration; Presentation of Clean Copies for Reprographic Use | Active | ||||
Publications in Sciences, Technology, Economy and Administration; Typographical Presentation | Active | ||||
Publications in Sciences, Technology, Economy and Administration; Presentation of Scientific and Technical Reports | Active | ||||
Medium type washers for pins | Withdrawn | ISO 8738 | |||
Clevis pins without head | Withdrawn | ISO 2340 | |||
Clevis pins with head | Withdrawn | ISO 2341 | |||
Legibility of Typefaces – General | Active | ||||
Lettering – Linear-Antiqua without serifes – General | Active | ||||
Typefaces – lineal Linear-Antiqua; lettering for transportation | Active | ||||
Lettering – Linear-Antiqua without serifes; lettering for printing | Active | ||||
Typefaces – lineal Linear-Antiqua; stenciled lettering for engraving and other processes | Active | ||||
Guidelines for the Establishment and Development of Thesauri; Monolingual Thesauri | Active | ||||
Guidelines for the Establishment and Development of Thesauri; Multilingual Thesauri | Active | ||||
Grooved Pins, Full Length Parallel-grooved with Pilot | Withdrawn | ISO 8739 | |||
Grooved Pins, Full Length Taper-grooved | Withdrawn | ISO 8744 | |||
Grooved Pins, Half Length Taper-grooved | Withdrawn | ISO 8745 | |||
Grooved Pins, Full Length Parallel-grooved with Chamfer | Withdrawn | ISO 8740 | |||
Grooved Pins, Half Length Reverse-grooved | Withdrawn | ISO 8741 | |||
Grooved Pins, Third Length Centre-grooved | Withdrawn | ISO 8742 | |||
Round Head Grooved Pins | Withdrawn | ISO 8746 | |||
Countersunk Head Grooved Pins | Withdrawn | ISO 8747 | |||
Spring-Type Straight Pins (Roll Pins) – Heavy Type | Withdrawn | ISO 8752 | |||
Bibliographic references to documents – Part 1: Full References to Printed and Published Documents | Active | ||||
Bibliographic references to documents – Part 2: Rules for Citing | Active | ||||
Bibliographic references to documents – Part 3: Indexes of cited documents (bibliographies) | Active | ||||
Pattern Equipment for Foundries; Production and Quality | Withdrawn | EN 12890 | |||
Tools for moulding – Part 1: Ejector pins with cylindrical head | Active | ||||
Tools for moulding – Part 2: Shouldered ejector pins | Active | ||||
Tools for moulding – Part 3: Ejector pins with conical head | Active | ||||
Hexagon domed cap nuts | Active | ||||
Soft Solders; Composition, Technical Delivery Condition | Active | ISO 9453 | |||
Aluminium and aluminium alloys – Unalloyed aluminium ingots for remelting – Specifications | Withdrawn | EN 576 | |||
Aluminium; Half-Finished Products | Withdrawn | EN 573-3 | |||
Strips, Plates and Sheets of Aluminium and Wrought | Withdrawn | EN 485-4 | |||
Seamless Drawn Copper Tubes for Piping Systems | Withdrawn | EN 1057 | |||
Round Rod of Aluminium (Highest Grade Aluminium) | Withdrawn | EN 754-3 | |||
Slotted Round Nut for Hook Spanner; ISO Metric Fine Thread | Active | ||||
Hook wrenches | Active | ||||
Round Nut with Set Pin Holes Inside; ISO Metric Fine Thread | Active | ||||
Spiral drill bits, short length | Active | ||||
Graphical Representation of Welded, Soldered and Brazed Joints | Withdrawn | ISO 17659 | |||
Graphical Representation of Welded, Soldered and Brazed Joints | Withdrawn | ISO 6947 | |||
Graphical Representation of Welded, Soldered and Brazed Joints; Concepts and Terms for Soldered and Brazed Joints and Seams | Active | ||||
Symbolic Representation on Drawings of Welded, Soldered and Brazed Joints | Withdrawn | ISO 2553 | |||
Construction contract procedures (VOB) – Part A: General provisions relating to the award of construction contracts | Active | ||||
Construction contract procedures (VOB) – Part B: General conditions of contract relating to the execution of construction work | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Alphanumeric office machines – Alphanumeric keyboards, keyboard arrangement for manually operated typewriters | Withdrawn | ||||
Alphanumeric office machines; alphanumeric keyboards, keyboard arrangement for electro-mechanical operated typewriters | Withdrawn | ||||
Active | |||||
Keyboards for data and text input – Part 2: Additional requirements | Active | ||||
Sets of 2 taps for metric fine ISO-threads M1 × 0,2 to M52 × 4 | Active | ||||
Vocabulary of terminology; basic concepts | Active | ||||
Seamless precision steel tubes – Part 1: Dimensions | Canceled | EN 10305-1 | |||
Seamless precision steel tubes – Part 2: Technical delivery conditions | Canceled | EN 10305-1 | |||
Seamless Steel Pipes and Tubes – Dimensions, Conventional Masses per Unit Length | Canceled | EN 10220 | |||
Blank flanges – Nominal pressure 6 to 100 | Withdrawn | EN 1092-1 | |||
Capillary Fittings; Bends 180° of Copper | Withdrawn | ||||
Steel threaded pipe fittings | Withdrawn | EN 10241 | |||
Pipe threads for tubes and fittings; parallel internal thread and taper external thread; tread dimensions | Withdrawn | EN 10226-1 | |||
Whitworth Pipe Threads for Tubes and Fittings; Cylindrical Internal Thread and Conical External Thread, Gauging System and Use of Gauges | Withdrawn | EN 10226-3 | |||
Whitworth Pipe Threads for Tubes and Fittings; Gauge Dimensions | Withdrawn | EN 10226-3 | |||
Pipe threads for tubes and fittings; sizes for taper screw limit plug gauges for parallel internal thread | Withdrawn | EN 10226-3 | |||
Whitworth Pipe Threads for Tubes and Fittings; Cylindrical Screw Limit Ring Gauges for Gauging Conical External Threads, Sizes | Withdrawn | EN 10226-3 | |||
Whitworth Pipe Threads for Tubes and Fittings; Conical Screw Check Plugs, Sizes | Withdrawn | EN 10226-3 |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
, | |||||
Hose clamps with worm gear drive; shape A | , | ||||
Hose clamps – Part 2: Clamps with fastening lugs | , | ||||
Hose clamps – Part 3: Bolt clamps | , | ||||
Hose clamps – Part 4: Technical delivery conditions | , | ||||
Hose clamps – Part 5: Wide strip hose clamps with fastening lugs; Types D and E | , | ||||
DIN 3113 | Combination Wrench | , | |||
Sealing rings ("O-rings") with special accuracy, made of elastomeric materials | Withdrawn | ||||
Fluid systems; O-rings; materials, field of application | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Water engineering, terms – Part 1: Dam plants | Active | ||||
Water engineering, terms – Part 2: Waterpower plants | Active | ||||
Correction of waterways, terms | Active | ||||
Subsoil, Field investigations – Part 1: Cone penetration tests | Active | ||||
Fire behaviour of building materials and elements – Part 1: Classification of building materials – Requirements and testing | Active | ||||
Fire Behaviour of Building Materials and Building Components – Part 2: Building Components; Definitions, Requirements and Tests | Active | ||||
Fire Behaviour of Building Materials and Building Components – Part 3: Fire Walls and Non-load-bearing External Walls; Definitions, Requirements and Tests | Active | ||||
Fire behaviour of building materials and elements – Part 4: Overview and design of classified building materials, elements and components | Active | ||||
Fire Behaviour of Building Materials and Building Components – Part 5: Fire Barriers, Barriers in Lift Wells and Glazings Resistant against Fire; Definitions, Requirements and Tests | Active | ||||
Fire Behaviour of Building Materials and Building Components – Part 6: Ventilation Ducts; Definitions, Requirements and Tests | Active | ||||
Fire behaviour of building materials and elements – Part 7: Roofing – Concepts, requirements and testing | Active | ||||
Fire behaviour of building materials and components – Part 8: Small-scale test furnace | Active | ||||
Fire behaviour of building materials and elements – Part 9: seals for cable penetrations; concepts, requirements and testing | Active | ||||
Fire behaviour of building materials and building components – Part 10: pipe encasements, pipe bushings, service shafts and ducts, and barriers across inspection openings; terminology, requirements and testing | Active | ||||
Fire behaviour of building materials and elements – Part 12: Fire resistance of electric cable systems required to maintain circuit integrity – Requirements and testing | Active | ||||
Fire behaviour of building materials and elements – Part 13: Fire resistant glazing; concepts, requirements and testing | Active | ||||
Fire behaviour of building materials and elements – Part 14: Determination of the burning behaviour of floor covering systems using a radiant heat source | Active | ||||
Fire behaviour of building materials and elements – Part 15: "Brandschacht" | Active | ||||
Fire behaviour of building materials and elements – Part 16: "Brandschacht" tests | Active | ||||
Fire behaviour of building materials and elements – Part 17: determination of melting point of mineral fibre insulating materials; concepts, requirements and testing | Active | ||||
Fire behaviour of building materials and components – Part 18: fire barriers, verification of automatic closure (continuous performance test) | Active | ||||
Fire behaviour of building materials and building components – Part 22: Application standard for DIN 4102-4 based on the design of partial safety factors | Active | ||||
Thermal protection and energy economy in buildings – Part 1: Quantities and units | Active | ||||
Thermal protection and energy economy in buildings – Part 2: Minimum requirements to thermal insulation | Active | ||||
Thermal protection and energy economy in buildings – Part 3: Protection against moisture subject to climate conditions; Requirements and directions for design and construction | Active | ||||
Thermal insulation and energy economy of buildings – Part 7: Airtightness of building, requirements, recommendations and examples for planning and performance | Active | ||||
Thermal insulation and energy economy in buildings – Part 10: Application-related requirements for thermal insulation materials – Factory made products | Active | ||||
Structural vibration – Part 1: Prediction of vibration parameters | Active | ||||
Structural vibration – Part 2: Human exposure to vibration in buildings | Active | ||||
Structural vibration – Part 3: Effects of vibration on structures | Active | ||||
Service and working scaffolds – Part 1: Service scaffolds – Performance requirements, general design, structural design | Active | ||||
Photographic sensitometry, determination of optical density: "Photographische Sensitometrie, Bestimmung der optischen Dichte" (1934-01, 1957–11, 1961–10) | Withdrawn | DIN 4512-1 1971-04, DIN 4512-3:1973-01, DIN 4512-4:1977-06, DIN 4512-5:1977-10, DIN 4512-6:1980-07 | |||
Photographic sensitometry, determination of the speed of black and white negative materials for pictorial photography (1971-04, 1993–05) | Withdrawn (2000–09) | DIN ISO 6 1996-02 | ISO 6 | ||
Photographic sensitometry, determination of diffuse transmission density (1973-01) | Withdrawn | DIN 4512-7 1993-01, DIN 4512-8:1993-01, DIN 4512-9:1993-01 | |||
Photographic sensitometry; determination of the speed of colour reversal films (1977-06, 1985–08) | Withdrawn (2002–06) | DIN ISO 2240 1998-06 | ISO 2240 | ||
Photographic sensitometry; determination of the speed of colour negative films (1977-10, 1990–11) | Withdrawn (2002–06) | DIN ISO 5800 1998-06 | ISO 5800 | ||
Photographic sensitometry; sensitometric illuminants and light sources (1980-07) | Withdrawn | ||||
Photographic sensitometry, determination of optical density; concepts, symbols and notations (1993-01) | Active | ||||
Photographic sensitometry, determination of optical density; geometric conditions for transmission density (1993-01) | Active | ||||
Photographic sensitometry, determination of optical density; spectral conditions (1993-01) | Active | ||||
Photographic sensitometry, determination of optical density; geometric conditions for reflection density (1993-01) | Active | ||||
Energy efficiency of heating and ventilation systems in buildings – Part 10: Heating, domestic hot water supply, ventilation | Active | ||||
Energetic evaluation of heating and ventilation systems in existing buildings – Part 12: Heat generation and domestic hot water generation | Active | ||||
Statistics on German meteorological data for calculating the energy requirements for heating and air conditioning equipment | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Rules for text presentation | Active | ||||
Physics of radiation in the field of optics and illuminating engineering – Part 1: Quantities, symbols and units of radiation physics | Active | ||||
Physics of radiation in the field of optics and illuminating engineering – Part 2: Evaluation of radiation by different detectors | Active | ||||
Physics of radiation in the field of optics and illuminating engineering – Part 3: Quantities, symbols and units of illuminating engineering | Active | ||||
Physics of radiation in the field of optics and illuminating engineering – Part 4: Efficiencies | Active | ||||
Physics of radiation in the field of optics and illuminating engineering – Part 5: Definitions for temperatures | Active | ||||
Physics of radiation in the field of optics and illuminating engineering – Part 6: Pupil intensity as a measure of retinal illumination | Active | ||||
Physics of radiation in the field of optics and illuminating engineering – Part 7: Terms for wavebands | Active | ||||
Physics of radiation in the field of optics and illuminating engineering – Part 8: Definitions and constants of radiation physics | Active | ||||
Physics of radiation in the field of optics and illuminating engineering – Part 9: Definitions in the field of luminescence | Active | ||||
Physics of radiation in the field of optics and illuminating engineering – Part 10: Photobiologically effective radiation, quantities, symbols and actions | Active | ||||
Artificial lighting – Part 3: Lighting of health care premises | Active | ||||
Artificial lighting – Part 6: Measurement and evaluation | Active | ||||
Artificial lighting – Part 7: Lighting of interiors with visual displays work stations | Active | ||||
Artificial lighting – Part 8: Workplace luminaries – Requirements, recommendations and proofing | Active | ||||
Clamp strength for woodworking | Active | ||||
Plane irons for wood smooth and for planes | Active | ||||
Curved irons for jack planes | Active | ||||
Lockwashers and locking plates for use with rolling bearings | Active | ||||
Splined joints, calculation of load capacity – Part 1: general basis | Active | ||||
Logic and set theory; symbols and concepts | Active | ||||
Signs in mathematical logic | Withdrawn | ||||
Complex quantities; nomenclature | Withdrawn | ||||
Involute splines based on reference diameters – Part 1: Generalities | Active | ||||
Involute splines based on reference diameters – Part 2: Nominal and inspection dimensions | Active | ||||
Involute splines based on reference diameters – Part 15: Inspection | Active | ||||
Time-dependent quantities – Part 1: Terms for the time-dependency | Active | ||||
Time-dependent quantities – Part 2: Letter symbols | Active | ||||
Time-dependent quantities – Part 3: Complex representation of sinusoidal time-dependent quantities | Active | ||||
Notation of matrices | Withdrawn | ||||
Fourier-, Laplace- and Z-transformation; symbols and concepts | Active | ||||
Directions and signs in electrical engineering; rules for electric and magnetic circuits, equivalent circuit diagrams | Withdrawn | EN 60375 | |||
Logarithmic quantities and units – Part 2: Logarithmic ratios, levels in nepers and decibels | Active | ||||
Fire test to railway components | Active | ||||
Compressed air equipment for rail vehicles – Pressure vessels made of steel – Dimensions, designation | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Knurled nuts | Active | ||||
Tommy screws with fixed clamping bolt | Active | ||||
Tommy nuts with fixed clamping bolt | Active | ||||
Tommy screws with movable clamping bolt | Active | ||||
Tommy nuts with movable clamping bolt | Active | ||||
Spring-loaded catch for jigs | Active | ||||
Thrust pads | Active | ||||
Clamp, straight | Active | ||||
Clamp, forked | Active | ||||
Goose neck clamp | Active | ||||
Stepped packing blocks as support for clamps | Active | ||||
Spherical washers and conical seats | Active | ||||
Feet with threaded shank for jigs and fixtures | Active | ||||
Support and location pins | Active | ||||
Slot stones, loose | Active | ||||
Parallel Pins, Hardened; Tolerance Zone m6 | Withdrawn | ISO 8734 | |||
Washers for clamping devices | Active | ||||
Paper and paper board – Lifespan classes | Active | ||||
Technical drawings, labeling | Withdrawn | ISO 3098 | |||
DIN 6796 | Conical spring washers for bolted connections | Active | |||
Toothed lock washers | Withdrawn | ||||
Serrated lock washers | Withdrawn | ||||
Lock washers (retaining washers) for shafts | Active | ||||
Bright Key Steel; Dimensions, Permissible Variations, Weights | Active | ||||
Drive Type Fastenings without Taper Action – Part 1: Parallel Keys, Keyways, Deep Pattern | Active | ||||
Drive Type Fastenings without Taper Action – Part 2: Parallel Keys, Keyways, Deep Pattern for Machine Tools, Dimensions and Application | Active | ||||
Drive Type Fastenings without Taper Action – Part 3: Parallel Keys, Shallow Pattern, Dimensions and Application | Active | ||||
Screw and Washer Assemblies | Withdrawn | EN 10644 | |||
Tapping screw and washer assemblies | Withdrawn | EN 10510 | |||
Plain washers for screw and washer assemblies | Withdrawn | EN 10673 | |||
Plain washers for tapping screw and washer assemblies | Withdrawn | EN 10669 | |||
Hexagon socket head cap screws with center, with low head | Active | ||||
High-strength hexagon head bolts with large widths across flats for structural steel bolting | Withdrawn | EN 14399-4 | |||
Steel hexagon nuts with large widths across flats for high-strength structural bolting | Withdrawn | EN 14399-4 | |||
Round washers for high-strength structural steel bolting | Withdrawn | EN 14399-6 | |||
Hexagon flange bolts | Withdrawn | EN 1665 | |||
Hexagon flange bolts with reduced shank | Withdrawn | EN 1665 | |||
Hexagon nuts with flange | Withdrawn | EN 1661 | |||
Prevailing torque type hexagon nuts with nonmetallic insert | Withdrawn | ISO 7040, ISO 10512 | |||
Prevailing torque type all-metal hexagon nuts | Withdrawn | ISO 7042, ISO 10513 | |||
Prevailing torque type hexagon nuts with flange and with non-metallic insert | Withdrawn | ISO 7043 (modified), ISO 12125 (modified) | |||
Prevailing torque type all-metal nuts with flange | Withdrawn | ISO 7044 (modified), ISO 12126 (modified) | |||
Cold bending of flat rolled steel | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Pan head screws with type H or type Z cross recess – product grade A | Active | ||||
Saw blades for web saws | Active | ||||
Break mandrel blind rivets | Withdrawn | ISO 14589, ISO 15977, ISO 15978, ISO 15979, ISO 15980, ISO 15981, ISO 15982, ISO 15983, ISO 15984, ISO 16582, ISO 16583, ISO 16584 | |||
Spiral Pins; Normal Type | Withdrawn | ISO 8750 | |||
Spiral Pins; Heavy Duty Type | Withdrawn | ISO 8748 | |||
Spring-Type Straight Pins; (Roll Pins) Light-weight Type | Withdrawn | ISO 13337 | |||
Plain Washers for Bolts with Heavy Clamping Sleeves | Active | ||||
Thread rolling screws for metric ISO thread – Part 1: Types, designation, requirements | Active | ||||
Thread rolling screws for ISO metric thread; guideline values for hole diameters | Active | ||||
Self-drilling screws with tapping screw thread – Dimensions, requirements and testing | Withdrawn | ISO 10666, ISO 15480, ISO 15481, ISO 15482, ISO 15483 | |||
Hexagon head and slotted head thread cutting screws – Dimensions, requirements and testing | Active | ||||
Cross recessed head thread cutting screws – Dimensions, requirements and testing | Active | ||||
Ring seals and gaskets | Active | ||||
Diving accessories for skin divers; terminology | Withdrawn | ||||
Diving accessories for skin divers; flippers; dimensions, requirements and testing | Withdrawn | ||||
Diving accessories for skin divers; diver's masks; requirements and testing | Withdrawn | ||||
Diving accessories for skin divers; snorkel; technical requirements of safety, testing | Withdrawn | ||||
Cross recesses for screws; (modified version of ISO 4757) | Withdrawn | ISO 4757 | |||
Threads and thread ends for tapping screws (modified version of ISO 1478) | Withdrawn | ISO 1478 | |||
Slotted pan head tapping screws | Withdrawn | ISO 1481 | |||
Slotted countersunk head tapping screws | Withdrawn | ISO 1482 | |||
Slotted raised countersunk head tapping screws | Withdrawn | ISO 1483 | |||
Taper Pins with Thread Ends and Constant Point Lengths | Withdrawn | ISO 8737 | |||
Taper Pins with Internal Thread | Withdrawn | ISO 8736 | |||
Parallel Pins with Internal Thread | Withdrawn | ISO 8733, ISO 8735 | |||
Spring lock washers with square ends for cheese head screws | Withdrawn | ||||
Cross recessed pan head tapping screws | Withdrawn | ISO 7049 | |||
Cross recessed countersunk head tapping screws | Withdrawn | ISO 7050 | |||
Countersunk (Flat) Head Tapping Screws with Cross Recess | Withdrawn | ISO 7051 | |||
Hexagon socket head cap screws with low head | Active | ||||
Cross recessed raised Phillips Pan head screws | Withdrawn | ISO 7045 | |||
Washers for steel structures – Product grade C | Active | ||||
Washers for steel structures – Product grade A | Active | ||||
Hexagon socket countersunk head cap screws | Withdrawn | ISO 10642 |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Polyethylene (PE) pipes – Dimensions | Active | ||||
Polyethylene (PE) pipes – PE 63, PE 80, PE 100, PE-HD – General quality requirements, testing | Active | ||||
Polypropylene (PP-R) Pipes -PN 20, PN25 PP-R – General quality requirements, testing | Active | ||||
Brazing and Braze Weld Filler Metals; Copper Base Brazing Alloys; Composition, Use, Technical Conditions of Delivery | Withdrawn | EN 1044 | |||
Brazing and Braze Weld Filler Metals; Silver-bearing Brazing Alloys with less than 20% by wt. Silver; Composition, Use, Technical Conditions of Delivery | Withdrawn | EN 1044 | |||
Brazing filler metals; silver brazing filler metals containing not less than 20% of silver; composition, application, technical delivery conditions | Withdrawn | EN 1044 | |||
Brazing and Braze Weld Filler Metals; Aluminium-Base Brazing Alloys; Composition, Use, Technical Conditions of Delivery | Withdrawn | EN 1044 | |||
Brazing filler metals; Nickel base filler metals for high temperature brazing; Application, composition, technical delivery conditions | Withdrawn | EN 1044 | |||
Manufacturing processes – Terms and definitions, division | Active | ||||
Narrow band saw blades for woodworking; dimensions | Active | ||||
Defects in Metallic Solder Joints; Brazing Joints and High-temperature Solder Joints; Classification, Designations, Explanatory Notes | Withdrawn |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Beta cotter pin (R pin) – Dimensions, materials | Active | ||||
Tubes for the food, chemical and pharmaceutical industry – Stainless steel tubes – Dimensions, materials | Withdrawn | EN 10357 | |||
DIN 11851 | Hygienic Unions |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Laboratory furniture; safety cabinets for microbiological and biotechnological work; safety requirements, tests | Withdrawn | ||||
Laboratory furniture; safety cabinets for microbiological and biotechnological work; containment of class 1 and class 2 cabinets, microbiological test | Withdrawn | ||||
Laboratory furniture; safety cabinets for microbiological and biotechnological work; requirements and testing | Withdrawn | ||||
Thermal solar systems and components – Solar collectors – Part 1: General requirements | |||||
Thermal solar systems and components – Solar collectors – Part 2: Test methods | |||||
Thermal solar systems and components – Factory made systems – Part 1: General requirements | |||||
Thermal solar systems and components – Factory made systems – Part 2: Test methods |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Division of hospitals into functional areas and functional sections | Active | ||||
Supply systems for medical gases – Part 2: Dimensions and allocation of probes and gas-specific connection points for terminal units for compressed medical gases and vacuum | Active | ||||
Packaging – Requirements for packaging recoverable through composting and biodegradation – Test scheme and evaluation criteria for the final acceptance of packaging | Active | DIN EN 13432 | |||
Workpiece corners and edges | Active | DIN ISO 13715(2000–12) |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Areas for the fire brigade on premises | Active | ||||
Fire precaution regulation – Part 1: General and part A (placard); rules for drafting and placarding | Active | ||||
Fire precaution regulation – Part 2: Part B (for persons without special tasks of fire prevention and fire fighting); rules for drafting | Active | ||||
Fire precaution regulation – Part 3: Part C (for persons with special tasks of fire prevention and fire fighting); rules for drafting | Active | ||||
Water pool for firefighting | Active | ||||
Ultrasonic domestic gas meters | Active | ||||
Portable fire extinguishers – Part 4: Maintenance | Active | ||||
Trailers for firefighting purposes, two-wheeled; general requirements | Withdrawn | ||||
Firefighting and rescue service vehicles – Vehicles for roller containers – General requirements | Active | ||||
Rescue service vehicles – Vehicles for roller containers – General requirements | Active | ||||
Trailers for portable fire pumps | Withdrawn | ||||
Firefighting – Trailer with removable foam-water monitor | Active | ||||
Fire fighting vehicles – Part 5: Group pumping appliance LF 10/6, Group pumping appliance for rescue operations HLF 10/6 | Active | ||||
Fire fighting vehicles – Part 11: Group pumping appliance LF 20/16, Group pumping appliance for rescue operations HLF 20/16 | Active | ||||
Fire fighting vehicles – Part 16: Pumping appliance TSF | Active | ||||
Fire fighting vehicles – Part 17: Pumping appliance TSF-W | Active | ||||
Fire fighting vehicles – Part 21: Pump water tanker TLF 20/40, Pump water tanker TLF 20/40-SL | Active | ||||
Fire fighting vehicles – Part 22: TLF 16/24-TR | Active | ||||
Fire fighting vehicles – Part 24: Small pumping appliance KLF | Active | ||||
Fire fighting vehicles – Part 25: Pumping appliance STLF 10/6 | Active | ||||
Vehicles carrying tools and gears – Part 1: General requirements | Active | ||||
Vehicles carrying tools and gears – Part 3: Emergency tender RW | Active | ||||
Vehicles carrying tools and gears – Part 12: Damage control tender GW-G | Active | ||||
Vehicles carrying tools and gears – Part 21: GW-L1 for logistic tasks | Active | ||||
Vehicles carrying tools and gears – Part 22: GW-L2 for logistic tasks | Active | ||||
Fire hose tender; Type SW 2000-TR | Withdrawn | ||||
Turntable ladders and similar fire fighting vehicles; Purpose, concepts, safety equipment, requirements | Withdrawn | EN 1777 | |||
Turntable ladders and similar fire fighting vehicles; Turn table ladders, engine driven | Withdrawn | EN 14043, EN 14044 | |||
Turntable ladders and similar fire fighting vehicles; Rescue baskets | Withdrawn | EN 1777 | |||
Turntable ladder DL 16–4, hand operating | Active | ||||
Trailer Ladder AL 16-4 | Active | ||||
Hook ladder, manufactured using wood; with hinged hook | Withdrawn | EN 1147 | |||
Hook light metal ladder | Withdrawn | ||||
Scaling ladder; made from wood | Withdrawn | EN 1147 | |||
Scaling ladder; made from light metal | Withdrawn | EN 1147 | |||
Scaling ladder; socket rungs and socket parts | Withdrawn | EN 1147 | |||
Folding ladder | Withdrawn | EN 1147 | |||
Three piece extension ladder made from wood | Withdrawn | EN 1147 | |||
Three piece extension ladder; made of light metal | Withdrawn | EN 1147 |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Cranes; steel structures; principles of design and construction | Active | ||||
Warehouse systems with guided industrial trucks; requirements on the ground, the warehouse and other requirements | Active | ||||
Warehousesystems with powered industrials trucks; code of practice for the protection of persons when operating with trucks in narrow aisles; safety requirements, testing | Active | ||||
Film 70 mm | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Classification of types | Active | ||||
Cross-linked high-density polyethylene (PE-X) pipes – General quality requirements and testing | Active | ||||
Cross-linked high-density polyethylene (PE-X) pipes – Dimensions | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Seamless Tubes of heat Resistant Steels | Withdrawn | ||||
Steels For Quenching And Tempering – Technical Delivery Conditions | Superseded | DIN 10083-1 DIN 10083-2 DIN 10083-3 | |||
Heat Resisting and Highly Heat Resisting Materials for Bolts and Nuts; Quality Specifications | Withdrawn | ||||
Materials for permanent magnets: Technical conditions | Active | ||||
Withdrawn | |||||
Withdrawn | |||||
Resistance alloys | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
House service connections facilities – Principles for planning | Active | ||||
Recesses for meter boards (electric meters) | Active | ||||
Foundation earth electrode – General planning criteria | Active | ||||
Electrical installations in residential buildings – Part 1: Planning principles | Active | ||||
Electrical installations in residential buildings – Part 2: Nature and extent of minimum equipment | Active | ||||
Electrical installations in residential buildings – Part 3: Wiring and disposition of electrical equipment | Active | ||||
Domestic kitchens, bathrooms and WCs; design principles | Withdrawn | ||||
Barrier-free built environment – Part 1: Streets, squares, paths, public transport, recreation areas and playgrounds – Design principles | Active | ||||
Construction of accessible buildings – Part 2: Publicly accessible buildings and workplaces, design principles | Active | ||||
Stairs in buildings – Terminology, measuring rules, main dimensions | Active | ||||
Construction contract procedures (VOB) – Part C: General technical specifications in construction contracts (ATV) – Installation of air conditioning systems | Active | ||||
Contract procedures for building works – Part C: General technical specifications for building works; Low-voltage installation and medium-voltage installation with nominal voltages up to including 36 kV | Active | ||||
Construction contract procedures (VOB) – Part C: General technical specifications in construction contracts (ATV); Installation of lightning protection systems | Active | ||||
Steel structures – Part 1: Design and construction | Withdrawn | DIN EN 1993 DIN EN 1090 | |||
Steel structures – Part 2: Analysis of safety against buckling of linear members and frames | Withdrawn | ||||
Steel structures – Part 3: Analysis of safety against buckling of plates | Withdrawn | ||||
Steel structures – Part 4: Analysis of safety against buckling of shells | Withdrawn | ||||
Steel structures – Part 5: Composite structures of steel and concrete – Design and construction | Withdrawn | ||||
Steel structures – Part 7: Execution and constructor's qualification | Active | EN 1090-2 |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Control technology – Terminology | Active | ||||
Measurement and control; terminology and classification of controllers | Active | ||||
Control technology – Part 1: General terms and definitions | Active | ||||
Control technology – Part 2: Terms and definitions; dynamic systems behaviour | Active | ||||
Control technology – Part 3: Terms and definitions of switching systems behaviour | Active | ||||
Control technology – Part 4: Terms and definitions of control systems | Active | ||||
Control technology – Part 5: Functional terms | Active | ||||
Control technology – Part 6: Terms and definitions of functional and constructional units | Active | ||||
Control technology; graphical symbols and identifying letters for process control engineering; symbolic representation for functions | Active | ||||
Control technology; graphical symbols and identifying letters for process control engineering; representation of details | Active | ||||
Measurement and control; control engineering vocabulary | Withdrawn | ||||
Control technology; graphical symbols and identifying letters for process control engineering; symbolic representation for functions | Withdrawn | ||||
Control technology; graphical symbols and identifying letters for process control engineering; representation of details | Active | ||||
Pipe-lines of high-density PE (high-density polyethylene) and low-density PE (low-density polyethylene) for drinking water supply; pipes, pipe connections and fittings for pipe-lines | Withdrawn | EN 12201-1, EN 12201-2, EN 12201-3, EN 12201-5 | |||
Hydraulic steel structures – Part 1: Criteria for design and calculation | Active | ||||
Hydraulic steel structures – Part 2: Design and manufacturing | Active | ||||
Hydraulic steel structures – Part 3: Electrical equipment | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
DIN 20066 | Fluid technology – hose lines, dimensions, specifications | ||||
DIN 20163 | Explosives work | ||||
DIN 21800 | Hammer and pick signs (mining symbol) | ||||
DIN 21908 | Mining crevice work; colours | ||||
DIN 22101 | Conveyor belt for bulk material, fundamentals, analysis and design | ||||
DIN 22107 | Arrangements for belt conveyor rollers | ||||
DIN 22112 | Rollers: dimensions, specifications, testing | ||||
DIN 23307 | Seat leathers for the mining industry (miner's apron) | ||||
DIN 23342 | Clothing for the mining industry – men's vest with 1/4 sleeves | ||||
DIN 23345 | Clothing for the mining industry – men's underpants 1/1 length (Long Johns) |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Ventilation and air conditioning – folded and welded rectangular sheet metal ducts | Withdrawn | ||||
Centralised lubrication systems – Concepts – Part 1: Classification | Active | ||||
Active | |||||
Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Ductile iron pressure pipes with socket with cement-mortar lining for gas and water pipelines; dimensions and masses | Withdrawn | EN 545, EN 969 | |||
Ductile iron pressure pipes with socket for gas and water pipelines rated for pressures over 4 bar up to and including 16 bar; dimensions and masses | Withdrawn | EN 969 |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Roller contact tipper vehicles, roller containers – Part 1: Roller contact tipper vehicles up to 26 t, roller containers type 1570 made from steel | Active | ||||
Roller contact tipper vehicles, roller containers – Part 2: Roller contact tipper vehicles up to 32 t, roller containers type 1570 made from steel | Active | ||||
Roller contact tipper vehicles, roller containers – Part 3: Roller contact tipper vehicles up to 12 t, roller containers type 900 made from steel | Active | ||||
Roller containers for the transport on road and rail | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Active | |||||
DIN 32676 | Tri-Clamp Fittings[2] | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Frequency and wave bands | Active | ||||
Guidelines for the user interface in multimedia equipment for general purpose use (IEC/TR 61997:2001) | Active | ||||
Road vehicles; degrees of protection (IP-code); protection against foreign objects; water and contact; electrical equipment | Active | ||||
Graphical symbols for use on equipment | Withdrawn | ||||
Graphical symbols for use on equipment; graphical symbols from ISO 7000 for electrical engineering | Active | ||||
Electric power technology – Current systems – Concepts, quantities, letter symbols | Active | ||||
Quantities used in alternating current theory – Part 2: Two-line circuits | Active | ||||
Quantities used in alternating current theory – Part 2: Multi-line circuits | Active | ||||
Telecommunications – Part 1: Basic concepts | Active | ||||
Transmission systems and two-ports; concepts and quantities | Active | ||||
Transmission systems and two-ports; symmetry characteristics of linear two-ports | Active | ||||
Transmission systems and two-ports; measures for attenuation | Active | ||||
Nominal value, limiting value, rated value, rating – concepts | Active | ||||
Electrical communication engineering; electromagnetic relays, definitions | Withdrawn | ||||
Electro Sheets; Magnetic Materials for Transformers | Withdrawn | ||||
Small transformers and chokes; strip-wound cut cores; types SM, SE, SU, SG and S3U; dimensions materials | Withdrawn | ||||
Small transformers and chokes; strip-wound cut cores; technical conditions of delivery for one phase applications; types SM, SE, SU and SG | Withdrawn | ||||
Small transformers and chokes; strip-wound cut cores; technical conditions of delivery for three phase applications; type S3U | Withdrawn | ||||
Nominal values of resistors and capacitors | Withdrawn | IEC 60063 | |||
Colour code for fixed resistors | Withdrawn | EN 60062 | |||
Circular connectors for radio and associated sound equipment three and five-pole connectors | Withdrawn | ||||
Two-part connectors for printed board, grid 2,54 mm; common mounting features; survey of types | Withdrawn | ||||
Two piece connectors for printed circuits, grid 2,54 mm (0,1 in); general allusions | Withdrawn | EN 60603-2 | |||
Two-part connectors for printed boards; grid 2,54mm; dimensions of types B, C and D | Withdrawn | EN 60603-2 | |||
Two part connectors for printed boards; grid 2,54mm; dimensions of types F and G | Withdrawn | EN 60603-2 | |||
Two-part connectors for printed boards; grid 2,54mm, dimensions of type H | Withdrawn | EN 60603-2 | |||
Two-part connectors for printed boards; grid 2,54mm; ratings, requirements, tests | Withdrawn | EN 60603-2 | |||
Two-part connection for printed boards; grid 2.54mm; dimensions of types Q, R and S | Withdrawn | EN 60603-2 | |||
Two-part connectors for printed boards; grid 2,54 mm; dimensions of types U and V | Withdrawn | EN 60603-2 | |||
Two-part connectors for printed boards; grid 2.54 mm; dimensions of type M | Withdrawn | EN 60603-2 | |||
Two-part connectors for printed boards; grid 2.54 mm; dimensions of type M; survey of special contracts for use with type M | Withdrawn | EN 60603-2 | |||
Two-part connectors for printed boards; grid 2,54 mm; dimensions of type E | Withdrawn | EN 60603-2 | |||
Two-part connectors for printed boards; grid 2,54mm; gauges | Withdrawn | EN 60603-2 | |||
Two-part connectors for printed boards; dimensions for type X | Withdrawn | ||||
Two-part connectors for printed boards; dimensions of type M | Withdrawn | ||||
Rack and panel connectors, trapezoidal, round contacts 1 mm; common mounting features and dimensions; survey of types | Active | ||||
Rack and panel connectors; trapezoidal, round contacts 1 mm; ratings, requirements, tests | Active | ||||
Rack and panel connectors, trapezoidal, round contacts ø1 mm; common mounting features and dimensions; survey of types | Active | ||||
Rack and panel connectors, trapezoidal, round contacts ø1 mm; ratings, requirements, tests | Active | ||||
Rack and panel connectors, trapezoidal, round contacts ø1 mm; dimensions of type A; solder termination for free wiring | Active | ||||
Rack and panel connectors, trapezoidal, round contacts ø1 mm; dimensions of type C; crimp termination for free wiring | Active | ||||
Guidelines for the presentation of published data | Withdrawn | IEC 60747-2 | |||
Thyristors, definitions | Withdrawn | ||||
Semiconductor devices and integrated circuits; kinds of devices and general terms | Withdrawn | ||||
Semiconductor devices and integrated circuits; optoelectronic semiconductor devices; terms and definitions | Withdrawn | ||||
Cases 10 A 3 and 10 B 3 for semiconductor devices; main dimensions | Withdrawn | ||||
Case 23 A 3 for semiconductor devices; main dimensions | Withdrawn | ||||
Cases 34 A 2 and 34 A 3 for semiconductor devices; main dimensions | Withdrawn | ||||
Case 11 A 3 and 11 B 3 for semiconductor devices; main dimensions | Withdrawn | ||||
Case 12 A 3 for semiconductor devices; main dimensions | Withdrawn | ||||
Case 13 A 3 for semiconductor devices; main dimensions | Withdrawn | ||||
Case 14 A 3 for semiconductor devices; main dimensions | Withdrawn | ||||
Case type 15 for semiconductor devices; main dimensions | Withdrawn | ||||
Cases type 5 for semiconductor devices and integrated circuits | Withdrawn | ||||
Cases 18 A, B and C with 2 up to 4 terminals for semiconductor devices; main dimensions | Withdrawn | ||||
Terminal markings for electrical equipment; general rules, alphanumeric system | Withdrawn | EN 60445 | |||
Terminal markings for power transformers and reactors | Active | ||||
Terminal markings for power converters | Withdrawn | IEC 61148 | |||
Totally enclosed fan-cooled three-phase induction motors squirrel-cage, type IM B 3, with rolling bearing; mounting dimensions and relationship frame sizes-output ratings | Withdrawn | ||||
Totally enclosed fan-cooled three-phase induction motors with squirrel-cage, type IM B 3, with rolling bearings; relationship frame sizes – output ratings for type of protection increased safety "e" | Active | ||||
Totally enclosed fan-cooled three-phase induction motors with squirrel-cage, type IM B 3, with rolling bearings; relationship frame sizes – output ratings for type of protection flameproof enclosure "d" | Active | ||||
Totally enclosed fan-cooled alternating-current polyphase motors with squirrel-cage, design B3, with ball bearings, maximum envelope dimensions | Active | ||||
Touch-protected connector for electromedicine | Active | ||||
Rating plates for rotating electrical machinery; design | Active | ||||
Rated output values for rotating electrical machinery for continuous duty | Active | ||||
Measurement and control – Measurement and control instruments for panel mounting – Nominal front- and cut-out-dimensions | Withdrawn | IEC 61554 | |||
Electrical measuring instruments; direct acting indicating electrical measuring instruments and their accessories | Withdrawn | EN 60051-1 | |||
Line scales and pointers for indicating electrical measuring instruments; general requirements | Active | ||||
Line scales and pointers for indicating electrical measuring instruments; designs and dimensions | Active | ||||
Line scales and pointers for indicating electrical measuring instruments; scale graduation and numbering | Active | ||||
Measuring and control; electrical measuring instruments; terminal markings for switchboard meters, panel meters and measuring transducers for the measurement of power and power factor | Active | ||||
Electricity meters, tariff time switches and ripple control receivers; connection diagrams, terminal marking, circuit diagrams | Active | ||||
Electricity meters – Part 2: Marking of auxiliary terminals for tariff devices according to IEC-Report 61354:1995 | Active | ||||
Meter mounting boards; dimensions based on a grid system | Active | ||||
Meter mounting boards; functional area | Active | ||||
Meter panels; wirings | Active | ||||
Modular electronics housings | Active | ||||
Meter mounting boards; dimensions based on a grid system | Active | ||||
Meter mounting boards; functional area | Active | ||||
Meter panels; wirings | Active | ||||
Meter panels; cover for wiring | Active | ||||
Thermistors; PTC, technical terms and tests | Withdrawn | ||||
Information processing; vocabulary | Withdrawn | ||||
Information processing – Concepts – General terms | Withdrawn | ||||
Information processing – Concepts – Representation of data | Withdrawn | ||||
Information processing – Concepts – Data structures | Withdrawn | ||||
Information processing – Concepts – Programming | Withdrawn | ||||
Information processing – Concepts – Components of digital computer systems | Withdrawn | ||||
Information processing – Concepts – Storage | Withdrawn | ||||
Information processing – Concepts – Times | Withdrawn | ||||
Information processing – Concepts – Processing functions | Withdrawn | ||||
Information processing – Concepts – Process relations and modes of operation | Withdrawn | ||||
Circular connectors for radio and associated sound equipment; six-pole connectors | Withdrawn | EN 60130-9 | |||
Connectors for coupling an external low-voltage power to portable entertainment equipment (describes at least two DC coaxial power plugs) | Active | ||||
High fidelity audio equipment and systems; minimum performance requirements; Part 1: general | Withdrawn | EN 61305-1 | |||
High fidelity audio equipment and systems; requirements for tuner equipments | Withdrawn | EN 61305-2 | |||
High fidelity audio equipment and systems; requirements for disk record reproducing equipments | Withdrawn | ||||
High fidelity audio equipment and systems; minimum performance requirements for magnetic recording and reproducing equipment | Withdrawn | ||||
High fidelity audio equipment and systems; minimum performance requirements for microphones | Withdrawn | ||||
High fidelity audio equipment and systems; minimum performance requirements for amplifiers | Withdrawn | EN 61305-3 | |||
High fidelity audio equipment and systems; requirements for loudspeakers | Withdrawn | EN 61305-5 | |||
High fidelity audio equipment and systems; for sets and systems | Withdrawn | ||||
High fidelity audio equipment and systems; minimum requirements for magnetic tapes 4 and 6 for audio recordings | Withdrawn | ||||
High fidelity audio equipment and systems; minimum performance requirements for headphones | Withdrawn | ||||
Measuring apparatus for frequency variations in sound recording equipment | Withdrawn | IEC 60386 | |||
Disk record reproducing equipment; directives for measurements, markings and audio frequency connections, dimensions of interchangeable pickups, requirements of play back amplifiers | Withdrawn | IEC 60098 | |||
Microphones; phantom powering | Withdrawn | ||||
Steel flats with special magnetic properties cold rolled, non – oriented, finally annealed magnetic sheet and strip hysteresis loss at frequencies above 100 Hz | Withdrawn | EN 10106 | |||
Grain-oriented magnetic steel and strip technical conditions | Withdrawn | EN 10107 | |||
Cords for telecommunication; code of insulated conductors, colour of sheath | Withdrawn | ||||
Terms of HF-lines | Active | ||||
Terms of HF-lines | Active | ||||
Definition of radio frequency transmission lines – mean characteristic impedance – mean standing wave ratio | Active | ||||
Lightning protection system; Arrangement of components and dimensions for mounting | Withdrawn | ||||
Lightning protection system; Description | Withdrawn |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Testing of floor coverings; determination of the anti-slip properties: wet-loaded barefoot areas; walking method; ramp test | Withdrawn | ||||
Testing of floor coverings; determination of the anti-slip properties: workrooms and fields of activities with slip danger, walking method – ramp test | Withdrawn | ||||
Lubricants; Lubricating Oils L-AN; Minimum Requirements | Withdrawn | ||||
Testing of particleboards; determination of formaldehyde emission by gas analysis | Withdrawn | EN 717-2 | |||
Paints and varnishes – Determination of the drying stage of coatings (modified Bandow-Wolff method) | Active | ||||
Testing of combustible materials; response to ignition by small flame | Active | ||||
Testing of Plastics; Flexural Test | Withdrawn | ISO 178 | |||
Flexible Cellular Polymeric Materials – Determination of Tear Strength | Withdrawn | ISO 8067 | |||
Testing of combustible materials; determination of ignition temperature | Active | ||||
Determination of burning behaviour using a gas burner | Active | ||||
Machine tools; symbols; numerically controlled machine tools | Withdrawn | ||||
Measuring Method for determination of solarization effect of fused silica optical fibers | Active | ||||
Surgical implants; threads for bone screws and nuts | Withdrawn | ||||
Thread connection for microscope objectives | Withdrawn | ISO 8038-1 |
DIN ISO 53438
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Information processing; switching algebra, mathematical signs and symbols | Active | ||||
Information processing; graphical symbols and their application | Active | ||||
Information processing; handwriting of the digit 0 and of the upper case letter O | Active | ||||
Information technology – 7-bit code | Active | ||||
Information processing – Coding on data media – Part 1: Representation of 7-bit code character sets on punched tape 25 | Active | ||||
Information processing – Coding on data media – Part 2: Representation of 7-bit coded and 8-bit coded character sets on punched cards | Active | ||||
Information processing – Coding on data media – Part 3: Representation of 7-bit coded and 8-bit coded character sets on magnetic tape 12 | Active | ||||
Information processing – Coding on data media – Part 4: Representation of 7-bit coded and 8-bit coded character sets on magnetic tape cassette 3,8 | Active | ||||
Information processing – Coding on data media – Part 5: Representation of 7-bit coded and 8-bit coded set on media-flexible disk cartridge | Active | ||||
Information processing; representation of packed numerics and binary data recorded on 9 tracks on magnetic tape 12 | Active | ||||
Presentation of ALGOL/ALCOR programs on paper tape and punch cards | Withdrawn | ||||
Font CMC 7 for magnetic ink character recognition; characters and nominal dimensions | Withdrawn | ISO 1004 | |||
Font A for optical character recognition; characters and nominal dimensions | Active | ||||
Font A for optical character recognition; characters and nominal dimensions; extension of the character set | Active | ||||
Font A for optical character recognition; representation of characters by dots in a 9 × 9 matrix | Active | ||||
Font B for optical character recognition; character | Withdrawn | ||||
Functional requirements for the interface between data terminal equipment and data circuit-terminating equipment – Part 1: General application | Active | ||||
List of definitions for interchange circuits between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) in public data networks | Active | ||||
Data transmission; interface between data circuit-terminating equipment (DCE) and data terminal equipment (DTE) | Active | ||||
Interface between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) for synchronous transmission on group band circuits at 48,000 bits per second | Active | ||||
Data transmission; interface between data circuit-terminating equipment (DCE) and data terminal equipment (DTE) | Active | ||||
Interface between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) for synchronous transmission on group band circuits at 48,000 bits per second | Active | ||||
Numerical control of machines, format; general requirements | Active | ||||
Industrial automation; numerical control of machines; format, preparatory and miscellaneous functions | Active | ||||
Withdrawn | |||||
Programming of numerically controlled machines; CLDATA, general structure and record types | Active | ||||
Programming of numerically controlled machines; CLDATA; minor elements of type 2000 records (post-processor commands) | Active | ||||
1998 | |||||
Active | |||||
Active | |||||
Withdrawn | |||||
Numerical control of machines; concepts | Withdrawn | ISO 2806 | |||
Interfaces and basic data link control procedures for data communication; C S-interface, V S-interface | Withdrawn | ||||
Interface and basic data link control procedures for data communication; balanced interface for start-stop transmission using basic data link control procedures on point-to-point connection | Withdrawn | ||||
Information processing; Nassi-Shneiderman flowchart symbols | Active | ||||
Industrial automation systems and integration – Multiprocessor Control System for Industrial Machines (MPST) – Part 1: Parallel bus | Active | ||||
Multiprocessor control system for industrial machines (MPST); industrial automatics; rules for information interchange | Active | ||||
Information technology – 8 bit code | Active | ||||
Industrial automation; Computer Aided Design; format for the exchange of standard parts data | Active | ||||
Local and Metropolitan Area Networks; LLC; identical with ISO 8802-2:1989 | Withdrawn | ISO 8802-2 | |||
Local and Metropolitan Area Networks; token-passing bus access method; identical with ISO/IEC 8802-4:1990 | Withdrawn | ISO/IEC 8802-4 | |||
Three-part standard regarding the seven security levels of paper shredders; replaces DIN 32757 | Active | ||||
Project controlling; project management; concepts | Active |
DIN | Title | Status | DIN replacement | Other org replacement | |
---|---|---|---|---|---|
Lubricating nipples; cone type | Active | ||||
Lead storage batteries; starter batteries for motorcycles, nominal capacities, main dimensions | Active | ||||
Lead storage batteries; starter batteries, terminals, vent plugs and filler openings | Active | ||||
Lead storage batteries; starter batteries for motor cycles and passenger cars | Active | ||||
Lead storage batteries; starter batteries for starting, lighting and ignition, 12 V, 27, 36, 45 and 54 Ah, for lateral basic fastening 10,5 | Active | ||||
Lead storage batteries; starter batteries for starting, lighting and ignition, 12 V, 27, 36, 45, 54 and 63 Ah, for lateral basic fastening 19 | Active | ||||
Lead storage batteries; starter batteries, protective covering for terminal | Active | ||||
Lead storage batteries; starter batteries with basic fastening 10,5 for passenger cars and commercial vehicles; nominal capacities, main dimensions | Active | ||||
Lead storage batteries; starter batteries for commercial vehicles; nominal capacities and main dimensions | Active | ||||
Lead storage batteries; starter batteries with 10,5 basic fastening lugs for commercial vehicles; nominal capacities and main dimensions | Active | ||||
Terminal markings for motor vehicles; scope, principles, requirements | Active | ||||
Terminal markings for motor vehicles; codes | Active | ||||
Terminal markings for motor vehicles; examples for application on circuit diagrams | Active | ||||
Terminal markings for motor vehicles; summary | Active | ||||
Radio communication devices in motor vehicles; installation space, general requirements | Active |