Kinematics equations are the constraint equations of a mechanical system such as a robot manipulator that define how input movement at one or more joints specifies the configuration of the device, in order to achieve a task position or end-effector location.[1] [2] Kinematics equations are used to analyze and design articulated systems ranging from four-bar linkages to serial and parallel robots.
Kinematics equations are constraint equations that characterize the geometric configuration of an articulated mechanical system. Therefore, these equations assume the links are rigid and the joints provide pure rotation or translation. Constraint equations of this type are known as holonomic constraints in the study of the dynamics of multi-body systems.
The kinematics equations for a mechanical system are formed as a sequence of rigid transformations along links and around joints in a mechanical system. The principle that the sequence of transformations around a loop must return to the identity provides what are known as the loop equations. An independent set of kinematics equations is assembled from the various sets of loop equations that are available in a mechanical system.
In 1955, Jacques Denavit and Richard Hartenberg introduced a convention for the definition of the joint matrices [Z] and link matrices [X] to standardize the coordinate frames for spatial linkages.[3] [4] This convention positions the joint frame so that it consists of a screw displacement along the Z-axis
[Zi]=\begin{bmatrix} \cos\thetai&-\sin\thetai&0&0\\ \sin\thetai&\cos\thetai&0&0\\ 0&0&1&di\\ 0&0&0&1 \end{bmatrix},
and it positions the link frame so it consists of a screw displacement along the X-axis,
[Xi]=\begin{bmatrix} 1&0&0&ai,i+1\\ 0&\cos\alphai,i+1&-\sin\alphai,i+1&0\\ 0&\sin\alphai,i+1&\cos\alphai,i+1&0\\ 0&0&0&1 \end{bmatrix}.
The kinematics equations are obtained using a rigid transformation [Z] to characterize the relative movement allowed at each joint and separate rigid transformation [X] to define the dimensions of each link.
The result is a sequence of rigid transformations alternating joint and link transformations from the base of the chain, around a loop, and back to the base to obtain the loop equation,
[Z1][X1][Z2][X2]\ldots[Xn-1][Zn]=[I].
The kinematics equations for a serial chain robot are obtained by formulating the loop equations in terms of a transformation [T] from the base to the end-effector, which is equated to the series of transformations along the robot. The result is,
[T]=[Z1][X1][Z2][X2]\ldots[Xn-1][Zn],
The kinematics equations for a parallel chain, or parallel robot, formed by an end-effector supported by multiple serial chains are obtained from the kinematics equations of each of the supporting serial chains. Suppose that m serial chains support the end-effector, then the transformation from the base to the end-effector is defined by m equations,
[T]=[Z1,j][X1,j][Z2,j][X2,j]\ldots[Xn-1,j][Zn,j], j=1,\ldots,m.
There are three Kinematic equations for linear (and generally uniform) motion. These are
Besides these equations, there is one more equation used for finding displacement from the 0th to the nth second. The equation is:
Sn=u+
| a | |
| 2 |
(2n-1)
The kinematics equations of serial and parallel robots can be viewed as relating parameters, such as joint angles, that are under the control of actuators to the position and orientation [T] of the end-effector.
From this point of view the kinematics equations can be used in two different ways. The first called forward kinematics uses specified values for the joint parameters to compute the end-effector position and orientation. The second called inverse kinematics uses the position and orientation of the end-effector to compute the joint parameters values.
Remarkably, while the forward kinematics of a serial chain is a direct calculation of a single matrix equation, the forward kinematics of a parallel chain requires the simultaneous solution of multiple matrix equations which presents a significant challenge.