The inner German border was a complex system of interlocking fortifications and security zones 1381km (858miles) long and several kilometres deep, running from the Baltic Sea to Czechoslovakia. The outer fences and walls were the most familiar and visible aspect of the system for Western visitors to the border zone, but they were merely the final obstacle for a would-be escapee from East Germany. The complexity of the border system increased steadily until it reached its full extent in the early 1980s. The following description and the accompanying diagram describe the border as it was around 1980.
Travelling notionally from east to west,[1] an escapee would first reach the edge of the restricted zone (Sperrzone), a closely controlled strip of land 5 kilometres (3.1 mi) wide, running parallel with the border. Evading the patrols and watchful inhabitants of the Sperrzone, the escapee would have reached the first of the border fences. The signal fence (Signalzaun), around 500mto1000mm (1,600feetto3,000feetm) from the actual border, was lined with low-voltage electrified barbed wire which activated alarms when touched or cut.
Beyond the signal fence was the "protective strip" (Schutzstreifen). It was brightly lit by floodlights in many places to reduce an escapee's chances of using the cover of darkness. Guard towers, bunkers and dog runs were positioned at frequent intervals to keep a round-the-clock watch over the strip. Crossing the Schutzstreifen, the escapee would next reach the floodlit control strip, often called the "death strip" in the West. Tripwire-activated flare launchers were situated at various points to help the border guards pinpoint the location of an escape attempt. The last and most formidable obstacle was the outer fencing. In some places there were multiple parallel rows of fences, each up to several metres high, with minefields in between. The fences were not electrified but were booby-trapped with directional anti-personnel mines at intervals of 10m (30feet), each one of which was capable of killing at a range of up to 120m (390feet). Finally, the escapee had to cross whatever natural obstacles were on the western side of the border fence as well as traversing a strip of cleared ground that was up to 500 meters (1640 ft) wide. While crossing this outer strip, the escapee would appear in clear view and shooting range of the border guards before reaching the safety of West German territory.
The Sperrzone, a 5km (03miles) wide area to which access was heavily restricted, was the rear segment of the border defences. When it was established in May 1952, it included a number of villages and valuable agricultural land. Although the land continued to be farmed where possible, many of the inhabitants were expelled on the grounds of political unreliability or simply because they lived inconveniently close to the border line. In some instances, entire villages were razed and the inhabitants relocated far to the east.[2]
Those who remained behind were required to be completely loyal to the regime and support the border guards, helping them by watching for strangers and unfamiliar vehicles. Even so, they had little freedom of movement; special permits were required to enter the zone and farmers worked under close supervision. They could enter and leave the zone an unlimited number of times but could not travel to other villages within the zone.[3] Curfews were imposed to prevent inhabitants from crossing the border under the cover of darkness.[4]
The Sperrzone was not fenced off but was marked with warning signs. The entry roads were controlled by checkpoints (Kontrollpassierpunkte) through which only authorised individuals could pass. The first layer of border fences, the signal fence, lay on the far side of the Sperrzone to control access to the protective strip or Schutzstreifen adjoining the border itself.
The signal or "hinterland" fence (Signalzaun) was the first of the border fences, dividing the Sperrzone from the more heavily guarded protective strip (Schutzstreifen) adjoining the actual border. Its purpose was to provide the guards with an early warning of an escape attempt. The fence itself was not a particularly formidable obstacle, standing only 2m (07feet) high. At the top, middle and bottom, rows of electrified barbed wire strands were attached to insulators. Cutting the wires or pulling them out of place resulted in an alarm being activated, alerting the guards to a possible breach of the fence. In practice, though, the border guards found that the fence frequently malfunctioned. The signal fence also had a 2adj=midNaNadj=mid control strip on its eastern side. The fence was built on open high ground wherever possible, to ensure that intruders would be silhouetted against the sky and thus be more easily spotted. By mid-1989, 1185km (736miles) of signal fencing had been constructed along the border.[5]
The border defences were monitored from hundreds of watchtowers regularly spaced along the Schutzstreifen. Initially they were simple wooden huts mounted on legs between 4mand12mm (13feetand39feetm) high, usually constructed from locally sourced timber. Most were replaced with concrete watchtowers from the late 1960s onwards in conjunction with the upgrading of the border defences.
By 1989, there were 529 concrete towers along the length of the inner German border and a further 155 towers of steel and wood construction, as well as various little-used observation platforms in trees. The concrete towers were prefabricated from sections that could be assembled within a few days. Their height could be varied by reducing the number of sections as required. They were connected to an electricity supply and telephone line and were equipped with a powerful 1,000-watt searchlight (Suchscheinwerfer) on the roof that could be directed at targets in any position around the watchtower. The windows could be opened to enable the guards to open fire without leaving the tower. In addition, the towers had firing ports emplaced in the side walls below the guard compartment.[6]
The towers were principally of three types:
Around a thousand observation bunkers also stood along the length of the border.[9] Most common was a small concrete bunker known as an "earth bunker" (Erdbunker), usually recessed into a depression in the ground with a view along the guard road and border fence. It was constructed from two base sections, each 0.8m (02.6feet) high with a cross-section of 1.8mx1.8mm (05.9feetx05.9feetm). It terminated in a third section that had two firing ports in the front side and one or two on each of the other sides. The roof was a separate component nesting on top of the concrete bunker, which could accommodate up to two soldiers.
Dog runs (Kettenlaufanlagen) were installed along high-risk sectors of the border. The dogs were generally chained to steel cables up to 100m (300feet) long. The dogs were occasionally turned loose in temporary pens adjoining gates or damaged sections of the fence. By the 1970s, there were 315 dog runs with 460 dogs. This figure increased steadily until a total length of 71.5km (44.4miles) of dog runs had been installed by mid-1989,[10] with 2,500 dogs employed as watchdogs and another 2,700 so-called "horse dogs".[11]
Rapid access to all parts of the border line was required to ensure a quick response to escape attempts. This was initially a problem for the East Germans, as few patrol roads existed along the border in its early years. Patrols typically used a footpath that ran inside of the fence, alongside the control strip.
When the "modern frontier" was constructed in the late 1960s, an all-weather patrol road (Kolonnenweg, literally "convoy path") was laid down to enable the guards to travel rapidly to any point along the border fence. It consisted of two parallel lines of perforated concrete blocks, each block measuring approximately 0.75m (02.46feet) wide and 2.5m (08.2feet) long. The blocks were pierced with four rows of rectangular concrete drainage holes. In some places they were laid crosswise to provide a continuous roadway. They were also occasionally used as foundation stones for structures such as towers and revetments and to create foundations on which towers were constructed.[12]
The Kolonnenweg usually ran between the control strip (on the border side) and the watchtowers (on the inland side). Around 900km (600miles) of patrol roads were built along the border, of which around 130km (80miles) was fully paved. In addition to the main Kolonnenweg, there were numerous short access roads built through forests and fields in the Schutzstreifen. Constructed from the same perforated concrete as the Kolonnenweg, these gave the border guards rapid access from the hinterland to the border line. Some civilians were permitted to use these access roads for forestry or farm work, though only with special permission.[13]
The control strips (Kontrollstreifen) were lines of bare earth running parallel to the border fences. They were not an obstacle as such but provided a simple and effective way for the border guards to monitor unauthorised travel across the border. It was almost impossible to cross the strip without leaving footprints, enabling the border guards to identify otherwise undetected escape attempts. They could learn how many individuals had crossed, where escape attempts were being made, and at which times of day escapees were active. From this information, the border guards were able to determine where and when patrols needed to be increased, where improved surveillance from watchtowers and bunkers was required, and which areas needed additional fortifications.
There were two control strips, both located on the inward-facing sides of the border fences. The secondary "K2" strip, 2m (07feet) wide, ran alongside the signal fence to the rear of the Schutzstreifen, while the primary "K6" strip, 6m (20feet) wide, ran along the inside of the border fence or wall. The K6 strip ran almost uninterrupted along the entire length of the border. Where it ran across roads, the road surface would be ripped up to make way for the control strip; where the border ran along streams and rivers, the strip was constructed parallel with the waterways.[14] In places where the border was prone to escape attempts, the control strip was illuminated at night by high-intensity floodlights (Beleuchtungsanlage) installed on concrete poles, which were also used at vulnerable points such as rivers and streams crossing the border. The strip was patrolled several times a day by guards, who would inspect it carefully for signs of intrusion.
In the West, the control strip became known as the "death strip" (Todesstreifen) because of the shoot-to-kill orders given to the border guards. The East Germans preferred to call it by the more euphemistic name of the "action strip" (Handlungsstreifen).[15] It was also nicknamed the Pieck-Allee ("Pieck Avenue") after East Germany's president Wilhelm Pieck (1949–60).[16]
The Soviets had pioneered the use of control strips on the borders of the USSR. The same technique was adapted for use in Germany when the border was first fortified from May 1952 onwards, at a time when it was still policed by Soviet troops. The construction of the control strip in 1952 was carried out by local villagers conscripted into work brigades. One of those involved, a resident of the Thuringian village of Kella, later recalled:
The control strips were later maintained by a specialist engineering corps, the Grenzpioniere. They used 3adj=midNaNadj=mid harrows towed by KT-50 bulldozers and copious quantities of herbicide to keep the strip free of vegetation.[13]
Anti-vehicle barriers along the inner German border grew increasingly impenetrable throughout its existence. In the early days, the East Germans blocked border crossings by simply tearing up the road surface, digging ditches and using the earth and rubble to build ramparts that physically blocked the carriageways. These were then enhanced with wire and wooden posts. As border fortifications developed into permanent barriers, purpose-built obstacles became standard. The most common types were Czech hedgehogs (Panzersperre) or cheval de frise (Stahligel or "steel hedgehogs"). These anti-vehicle devices were constructed from three or four pairs of 1.5adj=midNaNadj=mid rails welded together to form a steel obstacle weighing over 500kg (1,100lb) – heavy enough to stop a motor vehicle from pushing them aside.[17] Distributed at intervals narrow enough to prevent even the smallest East German vehicle, such as Trabants, from passing between them, they became a common sight along the entire inner German border and the Berlin Wall.[13]
Rows of anti-vehicle ditches, or Kraftfahrzeug Sperrgraben (KFZ-Sperrgraben), were built during the era of the "modern frontier". These lined 829km (515miles) of the border and were absent only where natural obstacles such as streams, rivers, gullies or thick forests made such barriers unnecessary. The ditches were constructed as a V-shaped cut about 0.8m (02.6feet) deep, with a steeply sloping western edge and shallow eastern edge. The western edge was faced with concrete slabs that were 15cm (06inches) deep. They proved to be an extremely effective obstacle, preventing almost any type of vehicle from crossing.
The border fences were constructed in a number of phases, starting with the initial fortification of the border from May 1952. The first-generation were crudely built barbed-wire fences (Stacheldrahtzäune) standing between 1.2mand2.5mm (03.9feetand08.2feetm) high. The fence was overlooked by watchtowers located at strategic intervals along the border. It was, however, a flawed obstacle. In some places it was so poorly constructed or maintained that livestock was able to wander unhindered across the border. In a few places, gaps were purposefully left with lowered gate poles in front of them and anti-vehicle Czech hedgehog barricades behind.[18]
The fences were strengthened in the late 1950s, particularly in areas with a high number of escapes. Parallel rows of barbed-wire fences were built, with concertina wire added between the fences in some places to further hinder escapees. The outer fence was often located very close to the actual border. A further obstacle was added by placing short wooden anchor posts about 2m (07feet) outwards from both fences. Barbed wire was strung between them to form a V-shape to hinder lateral movement by escapees. In some low-risk areas, only a single fence was installed.[19]
A "third generation" border fence, much more solidly constructed, was installed in an ongoing programme of improvements from the late 1960s to the 1980s. The entire fence line was moved back to create an outer strip (see below) between the fence and the actual border. The barbed-wire fences were replaced with a barrier that was usually between 3.2mand4mm (10.5feetand13feetm) high. It was constructed with expanded metal mesh (Metalgitterzaun) panels. The openings in the mesh were generally too small to provide finger-holds and were very sharp. The panels could not easily be pulled down, as they overlapped, and they could not be cut through with a bolt- or wire-cutter. Nor could they be tunnelled under easily, as the bottom segment of the fences was partially buried in the ground. In a number of places, more lightly constructed fences (Lichtsperren), consisting of mesh and barbed wire, lined the border.[20]
The fence was not continuous and could be crossed at a number of points other than the official border crossings. Gates were installed to enable border guards to patrol up to the border line and to give engineers maintenance access to the outward-facing side of the barrier. Like the fence itself, the gates were designed to be escape-proof. They were hinged from the outside but opened inwards and the pivot pins were welded to prevent their removal. They were chained and locked with heavy-duty padlocks, and a sharp saw-toothed steel strip was bolted to the top of the gates to prevent them from being climbed.
In some places, villages adjoining the border were fenced with wooden board fences (Holzlattenzaun) or concrete barrier walls (Betonsperrmauern) standing approximately 3m–4mm (10feet–13feetm) high. Windows in buildings adjoining the border were bricked or boarded up, and buildings deemed too close to the border were pulled down. The barrier walls stood along only a small percentage of the border – 29.1km (18.1miles) of the total length by 1989. A notorious example was in the divided village of Mödlareuth, where the border ran along the course of a stream that bisected the village. When the border was first fortified in 1952, a wooden board fence was erected just inside East German territory. It was replaced in 1966 by a 700adj=midNaNadj=mid, 3.3adj=midNaNadj=mid concrete wall built through the village on the East German side of the stream. The village was nicknamed "Little Berlin" for its resemblance to the divided city. The name was well-earned, as the wall was constructed along very similar lines to the one in Berlin. Like the Berlin Wall, its top was lined with sewer pipes or steel pipes to prevent it from being climbed and its interior perimeter was floodlit at night.[21]
The outer border fences were lined with anti-personnel mines designed to kill or injure would-be escapees. The mining of the border began in 1966; by the 1980s, some 1.3 million mines of various Soviet-made types had been laid. The mines were usually laid in a standardised pattern of a rectangular box, 23mby180mm (75feetby590feetm), containing three rows of mines. The most common type was the Soviet-made PMD-6M mine. However, its wooden construction made it unreliable and prone to decay. The PMD-6Ms were later replaced by more durable plastic mines of the PMN-2, PMP-71 and PPM-2 types. Most of the mines were pressure-activated, requiring someone to step on one to detonate it, with the exception of the tripwire-activated POMZ-2 stake mine. The minefields were not marked on the East German side, though Achtung! Minen! signs were often posted by the West Germans on their side. The mines were a hazard to civilians on both sides of the border; they were frequently set off by animals such as deer and could be washed out of position by rain or floods. It was not unknown for mines to travel hundreds of metres into fields and streams on either side of the border.[22]
In 1970, the East Germans began to introduce the SM-70 (Splittermine-70) directional anti-personnel mine, mounted on the border fence itself. Some 60,000 SM-70s were eventually installed. It was given various descriptions in the West such as "spring gun" or "self-firing device", though to the East Germans, it was known as the "automated firing device" (Selbstschußapparat). The device consisted of a horizontally oriented cone filled with 110g of TNT explosive into which was embedded approximately 80 small sharp-edged steel cubes. It was fitted to the inward-facing side of the border fence at intervals of around 10m (30feet). The device was triggered if the tripwire connected to the firing mechanism was pulled or cut.[23] It was potentially lethal to a maximum range of around 120m (390feet), though its effective lethal range was 25 metres (82 ft). On one occasion, when a deer fell victim to an SM-70, an observer noted that "an approximately 5 meter [20'] area appeared as if it had been worked over by a rake."[24] By 1976, SM-70s had been installed along 248 km (155 miles) of the border and conventional minefields lined another 491 km (305 miles).[25] The mines were eventually removed by the end of 1984 in the face of international condemnation of the East German government.
Until the late 1960s, the border fortifications were constructed almost up to the actual border line. The later "modern frontier", by contrast, incorporated a wide strip of cleared land on the western side in front of the border fence. The outer strip ranged in width from 20m (70feet) to as much as 2km (01miles). It gave the border guards a clear field of fire to target escapees who had made it over the fence and provided a buffer zone where engineers could work on maintaining the outward face of the border defences. Access to the outer strip was very tightly controlled to ensure that the guards themselves would not be tempted to escape. Although often described by Western sources as a "no-man's land", it was in fact wholly East German territory; trespassers could be arrested or shot.[26]
The actual border line between West and East Germany was located on the far side of the outer strip. It was marked by granite border stones (Grenzsteine), 20cm (10inches) square with a + carved on the top and the letters "DDR" on the east-facing edge. In August 1967, East Germany erected 2,622 distinctive border markers or "barber's poles" (Grenzsäule or Grenzpfähle), each located about 500feet apart. They were made of concrete and painted with the black, red and gold colours of the German flag. Some can still be seen in situ today. A metal East German coat of arms, the Staatsemblem, was fixed to the side of the column that faced West Germany. The column terminated in a metal spike to stop birds using the border markers as a perch and thereby prevent them from defecating on the coat of arms.[27]
On the West German side there were no barriers of any kind, nor even any patrol roads in most areas. Warning signs (Grenzschilder) with messages such as Achtung! Zonengrenze! ("Danger! Zonal border!") or Halt! Hier Zonengrenze ("Stop! The zonal border is here") notified visitors of the presence of the border. Signs in English and German provided notifications of the distance to the border to discourage accidental crossings. Foreign military personnel were restricted from approaching the border to avoid clashes or other unwanted incidents. No such restriction applied to Western civilians, who were free to go up to the border line. There were no physical obstacles to stop them actually crossing it, and there were incidents of West Germans crossing the border to steal East German border markers as souvenirs (at considerable risk, since the East German border guards sought to prevent such "provocations").[27]