| Evans Bay Patent Slip | |
| Nearest City: | Wellington |
| Built: | 1863 |
| Demolished: | 1980 |
| Current Use: | Public park |
| Owner: | Wellington City Council |
The Evans Bay Patent Slip is a heritage site of the former patent slip located in Evans Bay, in Wellington Harbour in the North Island of New Zealand. The first slipway on the site was commissioned in May 1863 to enable maintenance of the hulls of small vessels. The Wellington Provincial Council was keen to encourage shipping trade by improving facilities in Wellington Harbour and began planning later in 1863 for the construction of a larger patent slip. A concession was granted for the supply, construction and operation of a patent slip on the site. Equipment for the new slip was delivered in 1865 and 1866, but construction was delayed for several years because of a contractual dispute concerning the suitability of the design for the ground conditions. The original suppliers lost a court case and withdrew from the project. The Wellington Patent Slip Company was formed to take over the assets, and construction began in 1871. The Patent Slip was officially opened in March 1873.
A second slipway was constructed at the site in 1922. The original slip operated until 1969, and the second was closed on 31 July 1980. Most equipment has been removed from the site, and a residential development now occupies some of the original land. However, the site has been listed as a Category 2 historic place by Heritage New Zealand, and the area is classified as a heritage zone by the Wellington City Council.
In 1863, the New Zealand Steam Navigation Company decided to build a slip at Greta Point in Evans Bay to make it easier to repair and clean ships' hulls. A contract was let to shipwright Edward Thirkell, and by May 1863 the slip was in operation.[1] This first slip was long, with the upper part being bolted together so that it could be removed from under any ship if necessary. The slip itself consisted of two wooden "slideways" for the keel and the bilge, and the low end sat in eight feet (2.4 m) of water at low tide. Two manually-operated winches pulled ships up the runners.[2] Edward Thirkell managed this slip and its successor until his death in 1882.[3] The New Zealand Steam Navigation Company went into liquidation in 1871,[4] and management of the slip passed to the newly formed Patent Slip Company.[5] [6] The wooden slip was in use at least until 1873, when the new slip was built slightly south of it.[7]
The immediate success of the first slipway led the Wellington Provincial Counci
Kennards manufactured and delivered hundreds of tons of machinery to Wellington in 1866. However there was a contractual dispute about extra work required due to the nature of the site at Evans Bay, so the equipment sat there on the beach for five years while the dispute was discussed.[11] In 1871 Wellington businessmen formed the Wellington Patent Slip Company and bought the equipment from Kennards.[12] Construction began in 1871 and was completed in May 1873.[13] [14] The Evans Bay Patent Slip, the first in New Zealand, was a major engineering achievement. A 200-ton, 180adj=midNaNadj=mid cradle moved on wheels along parallel rails. Two chains were used for hauling vessels out of the water and lowering them back down. The chains ran over a cogwheel winch powered by two steam engines. The main 'hauling up' chain was long and weighed 62 tons. Each link was 18inches long and made of iron 3inches thick. One end of the chain was attached to the cradle and the other dropped into a 35adj=midNaNadj=mid well beneath the winding gear. The smaller 'lowering out' chain was a loop with links NaNinches thick. This was used for lowering ships down the slip and for bringing up the empty cradle.
Construction on land above the high tide line was straightforward, but work under the water was much more complicated. Workers in a diving bell excavated the sea floor, shifting rock into a shallow iron box which they slid under the edge of the diving bell to be hauled to the surface and removed. The men worked in shifts of four to six hours. After this stage, a diver worked to position piles and join pieces together. Concrete was mixed in a boat on the surface and sent underwater down a tube with a canvas hose at the end so that the diver could direct the concrete to where it was needed. The workers underwater could only work in good weather conditions: in a southerly the current was strong enough to lift a diver off the sea floor.[15] [16] This was the first large-scale underwater construction in New Zealand.[17] A 500feet jetty was also erected to improve communication with ships. Along with housing for the winches and boilers required to operate the slipways, there were some houses, a store, an inspector's office, a carpenter's shop, a messroom, and a blacksmith's shop.
On 2 May 1873, the 316-ton barque Cyprus was the first ship to use the slipway. If necessary, two ships could use the slip at the same time. The first ship would be raised up and then chocks put under it so that the cradle could be released and sent down to pull up a second ship.[18] A small vessel could be raised up the slip in about 20 minutes, and a larger ship could be raised at a rate of 15or. The press reported that the slip could handle ships weighing up to 2,000 tons and was "the finest and largest in the Australian colonies".[19] By the late 1890s there were calls for a dry dock in Wellington, amid claims that the Patent Slip could not cope with the increased size and number of ships visiting Wellington.[20]
Early in 1908, the Union Steam Ship Company acquired 90% of the shares in the Wellington Patent Slip Company.[21] In July 1908, after months of meetings and negotiations with the Patent Slip Company and the Union Steam Ship Company, Wellington Harbour Board acquired the property where the slip was located.[22] [23] Under the agreement, the Patent Slip Company would continue to manage the slip for the next 25 years and build a second slip if required. This was constructed in 1922. Also under the agreement, an area of land not required for slip operations was set aside for the use the Union Steam Ship Company for a 25-year period. After 25 years, the Harbour Board would pay the Patent Slip Company £30,000 and acquire the patent slip operation. The Harbour Board would also pay the USSCo for any improvements it made to the land it was using. The agreement expired in 1933 and after consultation and negotiation it was decided in 1935 that the Harbour Board would continue to lease Patent Slip Company operations and the land used by the USSCo to those two companies on periodic leases.[24] [25] In 1961, the Union Steamship Company chose not to renew its lease, so the Harbour Board took over management of both slips until 1969. At that time slipway No. 1 was taken out of service and slipway No. 2 was upgraded. The slipway closed on 31 July 1980. The site was demolished and various equipment scrapped, sold or given to museums, and land was filled in for a new housing subdivision.
The site was listed as a Category 2 historic place in 1982. Wellington City Council had the site rezoned as a heritage area in 2003, and the area is now known as Cog Park.
Over the many years of operation there were several significant incidents at the Patent Slip.
| Year | Vessel name | Type | Tonnage | Description | Reference | |
|---|---|---|---|---|---|---|
| 1878 | Large flywheel shattered, causing major damage to engine room and machinery | [26] | ||||
| 1909 | NZGSS Hinemoa | Steamer | 542 | Haul-out failure – fracture of 16adj=midNaNadj=mid main geared haul wheel | [27] | |
| 1914 | Karori | Steamer | 1863 | Fracture of haul chain – leading to uncontrolled re-entry to the water | [28] | |
| 1925 | Muritai | Harbour ferry | Vessel tailshaft dislodged coming off cradle leading to water ingress. Vessel was beached nearby. | [29] | ||
| 1926 | Kartigi | Steamer | 2347 | Fracture of haul chain | [30] | |
| 1935 | Natone | Tug | 75 | Tug heeled over and sustained damage during haul-out. Floating crane Hikitia used for recovery. | [31] | |
| 1947 | Tapuhi | Tug | 232 | Support cradle collapsed beneath tug | [32] |