Displacement (ship) explained
The displacement or displacement tonnage of a ship is its weight. As the term indicates, it is measured indirectly, using Archimedes' principle, by first calculating the volume of water displaced by the ship, then converting that value into weight. Traditionally, various measurement rules have been in use, giving various measures in long tons.[1] Today, tonnes are more commonly used.
Ship displacement varies by a vessel's degree of load, from its empty weight as designed (known as "lightweight tonnage"[2]) to its maximum load. Numerous specific terms are used to describe varying levels of load and trim, detailed below.
Ship displacement should not be confused with measurements of volume or capacity typically used for commercial vessels and measured by tonnage: net tonnage and gross tonnage.
Calculation
The process of determining a vessel's displacement begins with measuring its draft.[3] This is accomplished by means of its "draft marks". A merchant vessel has three matching sets: one mark each on the port and starboard sides forward, midships, and astern.[3] These marks allow a ship's displacement to be determined to an accuracy of 0.5%.[3]
The draft observed at each set of marks is averaged to find a mean draft. The ship's hydrostatic tables show the corresponding volume displaced.[4] To calculate the weight of the displaced water, it is necessary to know its density. Seawater (1,025 kg/m3) is more dense than fresh water (1,000 kg/m3);[5] so a ship will ride higher in salt water than in fresh. The density of water also varies with temperature.
Devices akin to slide rules have been available since the 1950s to aid in these calculations. Presently, it is done with computers.[6]
Displacement is usually measured in units of tonnes or long tons.[7]
Definitions
There are terms for the displacement of a vessel under specified conditions:
Loaded displacement
- Loaded displacement is the weight of the ship including cargo, passengers, fuel, water, stores, dunnage and such other items necessary for use on a voyage. These bring the ship down to its "load draft".
- Full load displacement and loaded displacement have almost identical definitions. Full load is defined as the displacement of a vessel when floating at its greatest allowable draft as approved by the load line assigning authority which is either the flag state (USCG etc) or a classification society (and designated by its "load line").[8] Warships have full load condition established through the Naval design process, and are exempt from commercial requirements laid out by flag state laws.[8]
Light displacement
- Light displacement (LDT) is defined as the weight of the ship excluding cargo, fuel, water, ballast, stores, passengers, crew, but with water in boilers to steaming level.[9]
Normal displacement
- Normal displacement is the ship's displacement "with all outfit, and two-thirds supply of stores, ammunition, etc., on board."[10]
Standard displacement
- Standard displacement, also known as "Washington displacement", is a specific term defined by the Washington Naval Treaty of 1922.[11] "It is the displacement of the ship complete, fully manned, engined, and equipped ready for sea, including all armament and ammunition, equipment, outfit, provisions and fresh water for crew, miscellaneous stores, and implements of every description that are intended to be carried in war, but without fuel or reserve boiler feed water on board."[11]
See also
References
Bibliography
- Book: Dear, I.C.B.
. Kemp . Peter . Oxford Companion to Ships and the Sea . Paperback . 2006 . Oxford University Press . Oxford . 0-19-920568-X .
- Book: George, William E. . Stability & Trim for the Ship's Officer . Cornell Maritime Press . Centreville, Md . 2005 . 0-87033-564-2 . registration .
- Book: Hayler, William B. . American Merchant Seaman's Manual . 2003 . Cornell Maritime Press . Cambridge, Md. 0-87033-549-9 . .
- Book: Turpin
, Edward A.
. McEwen, William A. . Merchant Marine Officers' Handbook . 4th . 1980 . Cornell Maritime Press . Centreville, MD . 0-87033-056-X .
- Web site: Nomenclature of Naval Vessels . Navy Department . 1942 . history.navy.mil . United States Navy .
- Web site: Definitions, Tonnages and Equivalents . 2008-03-24 . Military Sealift Command . Military Sealift Command . MSC Ship Inventory . United States Navy. https://web.archive.org/web/20070205160650/http://www.msc.navy.mil/inventory/glossary.htm . 2007-02-05 .
- Web site: Trim and Stability Information for Drydocking Calculations . 2008-03-24 . MLCPAC Naval Engineering Division . 2005-11-01 . United States Coast Guard.
- Book: United States of America. Papers Relating to the Foreign Relations of the United States: 1922. 1 . 1922 . 247–266 . Conference on the Limitation of Armament, 1922. http://www.ibiblio.org/pha/pre-war/1922/nav_lim.html .
- Book: United States Naval Institute . United States Naval Institute . Proceedings of the United States Naval Institute . 2008-03-24 . 1897 . United States Naval Institute .
Notes and References
- Web site: Ship Tonnage Explained - Displacement, Deadweight, Etc. . GG Archives . 2019-01-14.
- Web site: Dinsmore . Ben . 16 May 2011 . A Guide to Understanding Ship Weight and Tonnage Measurements . usurped . https://web.archive.org/web/20110529003954/http://www.themaritimesite.com/a-guide-to-understanding-ship-weight-and-tonnage-measurements/ . 29 May 2011 . 14 February 2018 . The Maritime Site.
- George, 2005. p. 5.
- George, 2005. p. 465.
- Turpin and McEwen, 1980.
- George, 2005. p. 262.
- Book: Chapman Great Sailing Ships of the World. Otmar Schäuffelen. Hearst Books. 2005. xix.
- Department of the Navy, 1942.
- Military Sealift Command.
- United States Naval Institute, 1897. p 809.
- Conference on the Limitation of Armament, 1922. Ch II, Part 4.