Compound steam engine explained

A compound steam engine unit is a type of steam engine where steam is expanded in two or more stages.A typical arrangement for a compound engine is that the steam is first expanded in a high-pressure (HP) cylinder, then having given up heat and losing pressure, it exhausts directly into one or more larger-volume low-pressure (LP) cylinders. Multiple-expansion engines employ additional cylinders, of progressively lower pressure, to extract further energy from the steam.

Invented in 1781, this technique was first employed on a Cornish beam engine in 1804. Around 1850, compound engines were first introduced into Lancashire textile mills.

Compound systems

There are many compound systems and configurations, but there are two basic types, according to how HP and LP piston strokes are phased and hence whether the HP exhaust is able to pass directly from HP to LP (Woolf compounds) or whether pressure fluctuation necessitates an intermediate "buffer" space in the form of a steam chest or pipe known as a receiver (receiver compounds).

In a single-expansion (or 'simple') steam engine, the high-pressure steam enters the cylinder at boiler pressure through an inlet valve. The steam pressure forces the piston down the cylinder, until the valve shuts (e.g. after 25% of the piston's stroke). After the steam supply is cut off the trapped steam continues to expand, pushing the piston to the end of its stroke, where the exhaust valve opens and expels the partially depleted steam to the atmosphere, or to a condenser. This "cut-off" allows much more work to be extracted, since the expansion of the steam is doing additional work beyond that done by the steam at boiler pressure.

An earlier cut-off increases the expansion ratio, which in principle allows more energy to be extracted and increases efficiency. Ideally, the steam would expand adiabatically, and the temperature would drop corresponding to the volume increase. However, in practice the material of the surrounding cylinder acts as a heat reservoir, cooling the steam in the earlier part of the expansion and heating it in the later part. These irreversible heat flows decrease the efficiency of the process, so that beyond a certain point, further increasing the expansion ratio would actually decrease efficiency, in addition to decreasing the mean effective pressure and thus the power of the engine.

Compounding engines

A solution to the dilemma was invented in 1804 by British engineer Arthur Woolf, who patented his Woolf high pressure compound engine in 1805. In the compound engine, high-pressure steam from the boiler first expands in a high-pressure (HP) cylinder and then enters one or more subsequent lower pressure (LP) cylinders. The complete expansion of the steam occurs across multiple cylinders and, as there is less expansion in each cylinder, the steam cools less in each cylinder, making higher expansion ratios practical and increasing the efficiency of the engine.

There are other advantages: as the temperature range is smaller, cylinder condensation is reduced. Loss due to condensation is restricted to the LP cylinder. Pressure difference is less in each cylinder so there is less steam leakage at the piston and valves. The turning moment is more uniform, so balancing is easier and a smaller flywheel may be used. Only the smaller HP cylinder needs to be built to withstand the highest pressure, which reduces the overall weight. Similarly, components are subject to less strain, so they can be lighter. The reciprocating parts of the engine are lighter, reducing the engine vibrations. The compound could be started at any point in the cycle, and in the event of mechanical failure the compound could be reset to act as a simple, and thus keep running.

To derive equal work from lower-pressure steam requires a larger cylinder volume as this steam occupies a greater volume. Therefore, the bore, and in rare cases the stroke as well, are increased in low-pressure cylinders, resulting in larger cylinders.

Double-expansion (usually just known as 'compound') engines expand the steam in two stages, but this does not imply that all such engines have two cylinders. They may have four cylinders working as two LP-HP pairs, or the work of the large LP cylinder can be split across two smaller cylinders, with one HP cylinder exhausting into either LP cylinder, giving a 3-cylinder layout where the cylinder and piston diameter of all three are about the same, making the reciprocating masses easier to balance.

Two-cylinder compounds can be arranged as:

The adoption of compounding was widespread for stationary industrial units where the need was for increased power at decreasing cost, and almost universal for marine engines after 1880. It was not widely used in railway locomotives where it was often perceived as complicated and unsuitable for the harsh railway operating environment and limited space afforded by the loading gauge (particularly in Britain). Compounding was never common on British railways and not employed at all after 1930, but was used in a limited way in many other countries.

The first successful attempt to fly a heavier-than-air fixed-wing aircraft solely on steam power occurred in 1933, when George and William Besler converted a Travel Air 2000 biplane to fly on a 150 hp angle-compound V-twin steam engine of their own design instead of the usual Curtiss OX-5 inline or radial aviation gasoline engine it would have normally used.[1] [2]

Multiple-expansion engines

It is a logical extension of the compound engine (described above) to split the expansion into yet more stages to increase efficiency. The result is the multiple-expansion engine. Such engines use either three or four expansion stages and are known as triple- and quadruple-expansion engines respectively. These engines use a series of double-acting cylinders of progressively increasing diameter and/or stroke and hence volume. These cylinders are designed to divide the work into three or four equal portions, one for each expansion stage. The adjacent image shows an animation of a triple-expansion engine. The steam travels through the engine from left to right. The valve chest for each of the cylinders is to the left of the corresponding cylinder.

History

Early work

Double-expansion

Multiple-expansion

Applications

Pumping engines

See main article: Cornish engine.

Mill engines

See main article: Stationary steam engine. Though the first mills were driven by water power, once steam engines were adopted the manufacturer no longer needed to site the mills by running water. Cotton spinning required ever larger mills to fulfil the demand, and this drove the owners to demand increasingly powerful engines. When boiler pressure had exceeded 60 psi, compound engines achieved a thermo-dynamic advantage, but it was the mechanical advantages of the smoother stroke that was the deciding factor in the adoption of compounds. In 1859, there was 75,886 ihp (indicated horsepower) of engines in mills in the Manchester area, of which 32,282 ihp was provided by compounds though only 41,189 ihp was generated from boilers operated at over 60psi.

To generalise, between 1860 and 1926 all Lancashire mills were driven by compounds. The last compound built was by Buckley and Taylor for Wye No.2 mill, Shaw. This engine was a cross-compound design to 2,500 ihp, driving a 24 ft, 90 ton flywheel, and operated until 1965.

Marine applications

See main article: Marine steam engine. In the marine environment, the general requirement was for autonomy and increased operating range, as ships had to carry their coal supplies. The old salt-water boiler was thus no longer adequate and had to be replaced by a closed fresh-water circuit with condenser. The result from 1880 onwards was the multiple-expansion engine using three or four expansion stages (triple- and quadruple-expansion engines). These engines used a series of double-acting cylinders of progressively increasing diameter and/or stroke (and hence volume) designed to divide the work into three or four, as appropriate, equal portions for each expansion stage. Where space is at a premium, two smaller cylinders of a large sum volume might be used for the low-pressure stage. Multiple-expansion engines typically had the cylinders arranged in-line, but various other formations were used. In the late 19th century, the Yarrow-Schlick-Tweedy balancing 'system' was used on some marine triple-expansion engines. Y-S-T engines divided the low-pressure expansion stages between two cylinders, one at each end of the engine. This allowed the crankshaft to be better balanced, resulting in a smoother, faster-responding engine which ran with less vibration. This made the 4-cylinder triple-expansion engine popular with large passenger liners (such as the Olympic class), but was ultimately replaced by the virtually vibration-free steam turbine.

The development of this type of engine was important for its use in steamships as by exhausting to a condenser the water could be reclaimed to feed the boiler, which was unable to use seawater. Land-based steam engines could simply exhaust much of their steam, as feed water was usually readily available. Prior to and during World War II, the expansion engine dominated marine applications where high vessel speed was not essential. It was superseded by the steam turbine when speed was required, such as for warships and ocean liners. HMS Dreadnought of 1905 was the first major warship to replace the proven technology of the reciprocating engine with the then-novel steam turbine.

Application to railway locomotives

See main article: Compound locomotive. For railway locomotive applications the main benefit sought from compounding was economy in fuel and water consumption plus high power/weight ratio due to temperature and pressure drop taking place over a longer cycle, this resulting in increased efficiency; additional perceived advantages included more even torque.

While designs for compound locomotives may date as far back as James Samuel's 1856 patent for a "continuous expansion locomotive", the practical history of railway compounding begins with Anatole Mallet's designs in the 1870s. Mallet locomotives were operated in the United States up to the end of mainline steam by the Norfolk and Western Railway. The designs of Alfred George de Glehn in France also saw significant use, especially in the rebuilds of André Chapelon. A wide variety of compound designs were tried around 1900, but most were short-lived in popularity, due to their complexity and maintenance liability. In the 20th century the superheater was widely adopted, and the vast majority of steam locomotives were simple-expansion (with some compound locomotives converted to simple). It was realised by engineers that locomotives at steady speed were worked most efficiently with a wide-open regulator and early cut-off, the latter being set via the reversing gear. A locomotive operating at very early cut-off of steam (e.g. at 15% of the piston stroke) allows maximum expansion of the steam, with less wasted energy at the end of the stroke. Superheating eliminates the condensation and rapid loss of pressure that would otherwise occur with such expansion.

Large American locomotives used two cross-compound steam-driven air compressors, e.g. the Westinghouse 8 1/2" 150-D,[14] for the train brakes.

The Yarrow-Schlick-Tweedy system

The presentation follows Sommerfeld's textbook, which contains a diagram (Figure 17) that is not reproduced for copyright reasons.[15]

Consider a 4-cylinder engine on a ship. Let x be the vertical direction, z be the fore-aft direction, and y be the port-starboard direction. Let the 4 cylinders be mounted in a row along the z-axis, so that their pistons are pointed downwards. The pistons are connected to the same crankshaft via long vertical rods. Now, we set up the fundamental quantities of the engine:

M1,M2,M3,M4

be the effective masses of the compounded piston-rod system of each cylinder.

a2

along the z-axis, and similarly for

a3,a4

.

l1,l2,l3,l4

be the length of each rod of the cylinder.

r1,r2,r3,r4

be the radii of the crankshaft connector of each cylinder.

\phi1,\phi2,\phi3,\phi4

be the angle of the crankshaft connector of each cylinder.

\phii-\phi1

is a constant

\alphai

for each of

i=2,3,4

.

Now, as the engine operates, the vertical position of cylinder

i

is equal to

xi

. By trigonometry, we have

x_i =r_i \cos\phi_i + \sqrt = l_1 + r_i\cos\phi_i - \frac (1-\cos(2\phi_i))/2 + O(r_i^3/l^2)

As each cylinder moves up and down, it exerts a vertical force on its mounting frame equaling

Mi\ddotxi

. The YST system aims to make sure that the total of all 4 forces cancels out as exactly as possible. Specifically, it aims to make sure that the total force (along the x-axis) and the total torque (around the y-axis) are both zero:

\sum_^4 M_i \ddot x_i = 0; \quad \sum_^4 M_i a_i\ddot x_i = 0

This can be achieved if

\sum_^4 M_i x_i = Const; \quad \sum_^4 M_i a_i x_i = Const

Now, plugging in the equations, we find that it means (up to second-order)

\sum_^4 M_i (r_i \cos\phi_i - \frac \cos(2\phi_i))= 0; \quad \sum_^4 M_i a_i (r_i \cos\phi_i - \frac \cos(2\phi_i)) = 0

Plugging in

\phii=\phi1+\alphai

, and expand the cosine functions, we see that with

\phi1

arbitrary, the factors of

\sin(\phi1),\cos(\phi1),\sin(2\phi1),\cos(2\phi1)

must vanish separately. This gives us 8 equations to solve, which is in general possible if there are at least 8 variables of the system that we can vary.

Of the variables of the system,

Mi,ri

are fixed by the design of the cylinders. Also, the absolute values of

a2,a3,a4

do not matter, only their ratios matter. Together, this gives us 9 variables to vary:

l1,l2,l3,l4,

a3
a2

,

a4
a2

,\alpha2,\alpha3,\alpha4

.

The YST system requires at least 4 cylinders. With 3 cylinders, the same derivation gives us only 6 variables to vary, which is insufficient to solve all 8 equations.

The YST system is used on ships such as the SS Kaiser Wilhelm der Grosse and SS Deutschland (1900).[16]

See also

External links

Notes and References

  1. https://books.google.com/books?id=AygDAAAAMBAJ&pg=PA9 "World's First Steam Driven Airplane"
  2. George & William Besler . The Besler Steam Plane . YouTube . Bomberguy . 29 April 2011.
  3. Encyclopædia Britannica Online, retrieved 29 March 2007.
  4. Web site: Richard Trevithick . Asme.org . 2017-04-30.
  5. Löhnis . Th. P. . 1916 . De Maatschappij voor scheeps- en werktuigbouw Fijenoord te Rotterdam, voorheen de Nederlandsche Stoomboot Maatschappij . Tijdschrift voor economische geographie . 137–138 . Delpher.nl.
  6. News: 1834 . August 29 . Ijzeren Spoorweg . 6 . Algemeen Handelsblad .
  7. Book: Lintsen, H.W. . Geschiedenis van de techniek in Nederland. De wording van een moderne samenleving 1800-1890. Deel V . 1994 . Dutch.
  8. Book: Clark, Arthur H. . 1911. The Clipper Ship Era 1843-1869 . New York . G.P. Putnam Sons .
  9. National Maritime Museum, Greenwich, UK, http://collections.rmg.co.uk/collections/objects/66013.html
  10. Book: Jarvis, Adrian . Robert . Gardiner . Dr Basil . Greenhill . 1993 . The Advent of Steam – The Merchant Steamship before 1900 . Conway Maritime Press . 158–159 . 9: Alfred Holt and the Compound Engine . 0-85177-563-2.
  11. Day, Lance and McNeil, Ian (Editors) 2013, Biographical Dictionary of the History of Technology Routledge, (P. 694)
  12. Book: Griffiths, Denis. Robert. Gardiner. Dr. Basil. Greenhill. The Advent of Steam - The Merchant Steamship before 1900 . Conway Maritime Press Ltd . 1993 . 106–126. Chapter 5: Triple Expansion and the First Shipping Revolution . 0-85177-563-2.
  13. Book: Man of War a History of the Combat Vessel. Macintyre. Donald. Bathe. Basil W. Mcgraw-hill Inc. 1974. 9780070445857. 95. Reference to the first battle ship with triple-expansion steam engines.
  14. 1941 Locomotive Cyclopedia of American Practice, Eleventh Edition, Simmons-Boardman Publishing Corporation, 30 Church Street, New York p.813
  15. Book: Sommerfeld, Arnold . Mechanics: Lectures on Theoretical Physics . 1950 . Academic Press . 978-1-4832-2028-4 . 76–98 . en.
  16. Sommerfeld . A. . May 1904 . The Scientific Results and Aims of Modern Applied Mechanics . The Mathematical Gazette . en . 3 . 45 . 26–31 . 10.2307/3603435 . 3603435 . 125314831 . 0025-5572.