| Camera Name: | Canon New F-1 |
| Focus: | Manual |
| Frame-Rate: | Manual lever winding, unmodified |
| Fsynch: | 1/90 s |
| Speedrange: | ISO 6 to 6400 [manual] |
| Shutter: | Titanium, four-shaft, horizontal-travel focal plane shutter |
| Shutterrange: | 8 s to 1/60 s [electronic]1/90 s to 1/2000 s [mechanical] |
| Exposure: | Shutter priority, aperture priority, manual |
| Metering: | EV-1 to EV20 @ ASA 100 |
| Battery: | 4LR44 6V battery or 4 LR44 1.5 volt batteries |
| Dimensions: | 96.6 × 146.7 × 48.3 mm |
| Weight: | 795 g |
| Made In: | Japan |
| Predecessor: | Canon F-1(n) |
The Canon New F-1 replaced the F-1n (an upgraded F-1) as Canon's top-of-the-line 35mm single-lens reflex camera in September 1981. Like the earlier models, the New F-1 takes FD-mount lenses. Although no date has ever been confirmed, it is thought that the last New F-1 was made in 1992. It was officially discontinued in 1994, and factory support ended in 2004.
The New F-1 is a manual-exposure camera capable of TTL full-aperture metering and stopped-down metering with the included Eye-Level Finder FN using a match-needle metering system. Aperture priority autoexposure is available by attaching the optional AE Finder FN. Also, shutter priority mode is optionally available when using either AE Motor Drive FN or AE Power Winder FN.[1] The New F-1 is also capable of operating in aperture priority mode with earlier Canon lenses which do not have an automatic diaphragm.
Batteries are housed behind the right-hand grip on the front of the camera.
Shutter speed timing is provided by both mechanical and electronic methods. In the manual exposure mode, the camera uses mechanical timing for the fast speeds (– s + X (flash synch, s) and B) and electronic timing for the slow speeds (– 8 s). When aperture-priority autoexposure is used, all shutter speeds are electronically timed, and the fastest speed is reduced to s.
Metering patterns are determined by the focusing screen in use, as each focusing screen incorporates a beam-splitter grating to redirect some light to the silicon photodiode metering cell in the body; in the previous F-1, the light-splitting device was a partially-silvered mirror in the condenser, which was mounted in the body. With many of the screens, the New F-1 has a choice between center-weighted averaging, selective-area (a rectangular frame in the center, covering approximately 12% of the overall frame area, similar to the prior F-1), or spot metering patterns (a circular frame in the center, covering approximately 3% of the overall frame area).
The New F-1 is an expandable system. It includes interchangeable viewfinders, focusing screens, motor drives, and alternate backs, all of which are specific to the New F-1. All other Canon components, such as the FD lens series, close up accessories (bellows, extension tubes, etc.), and Canon A and T Speedlights (except the 300TL) are also compatible with the system.
The New F-1 system has 5 different viewfinders, which can be quickly and easily changed by depressing the two buttons on the rear of the finder, pulling it off the camera body, and pushing the new finder into place.
The New F-1 system also has 13 different focusing screen styles, each of which has a variant for metering mode (either center-weighted averaging, selective (partial)-area, or spot, though not all are available with spot metering), for a total of 32 different screens.
The screens are named with a two-letter designation, the first indicating the metering type (A for averaging, P for partial-area metering, and S for spot metering), and the second indicating the style of screen, as listed below. For instance, the standard screen supplied from the factory in F-1 bodies is the Focusing Screen FN-AE (averaging metering, Type E "New Split/Microprism" style) for bodies shipped with an AE finder FN, and FN-PE (partial metering, new split/microprism style) for bodies shipped with an Eye Level Finder FN.
| Metering | Image | Field | Center focusing aid | Notes | ||||
|---|---|---|---|---|---|---|---|---|
| A(vg) | P(art) | S(pot) | ||||||
| A | Laser matte Fresnel | Microprism spot, 3.5 mm dia. | "Standard Microprism": Suitable for general photography. Microprism angle 8°; base size 0.12 mm square. | |||||
| B | Laser matte Fresnel | Split-image rangefinder spot (horizontal), 4 mm dia. | "New Split": Suitable for general photography. Split angles 5°40′ and 10°50′ on 0.012 mm pitch. | |||||
| C | Laser matte Fresnel | [none] | "Overall Laser Matte": Suitable for general photography; ideal for macro and telephoto lenses. | |||||
| D | Laser matte Fresnel | [none] | "Laser Matte with Grid": Includes etched grid of vertical and horizontal lines each 0.03 mm wide, spaced at 7 mm, otherwise similar to Type C. | |||||
| E | Laser matte Fresnel | Split-image rangefinder spot (horizontal) with microprism collar, 5 mm dia. | "New Split/Microprism": Suitable for general photography. Combines Types A and B. | |||||
| F | Laser matte Fresnel | Microprism spot, 3.5 mm dia. | "Microprism/Fast Lenses": Suitable for general photography with fast lenses (maximum aperture ≤), otherwise similar to Type A. Microprism angle 14°; base size 0.12 mm square. | |||||
| G | Laser matte Fresnel | Microprism spot, 3.5 mm dia. | "Microprism/Slow Lenses": Suitable for general photography with slow lenses (maximum aperture ≥), otherwise similar to Type A. Microprism angle 4°; base size 0.12 mm square. | |||||
| H | Laser matte Fresnel | Fine-ground matte spot | "Laser Matte with Scale": Includes horizontal (32 mm) and vertical (20 mm) scales ruled at 1 mm for scientific or close-up work, but can be used for general photography. Lines are 0.02 mm wide; includes grading along edges. | |||||
| I | Laser matte Fresnel | Double cross-hair reticle, 5 mm dia. | "Laser Matte with Double Cross-Hair Reticle": Intended for high-magnification work; uses parallax focusing. Cross-hairs are 3 mm × 3 mm, spaced 0.04 mm apart; line width is 0.02 mm. | |||||
| J | Bright laser matte | [none] | "Bright Laser Matte/Short Lenses": Intended for lenses with focal lengths of 50 to 200 mm. | |||||
| K | Bright laser matte | [none] | "Bright Laser Matte/Long Lenses": Intended for lenses with focal lengths ≥ 300 mm. | |||||
| L | Laser matte Fresnel | Double split-image rangefinder, 4 mm dia. | "Cross Split": Divides subject both horizontally and vertically. Split angle 8°. | |||||
| M | Laser matte Fresnel | [none] | "A/B Size Laser Matte": Includes cross marks to indicate corners of A/B ISO paper sizes with 1.41:1 aspect ratio, spaced to cover an area 30.55 mm × 21.6 mm. |
Replacing a screen is a simple operation. The finder is removed from the camera, and the screen is then pried up using a fingernail along the silver rear edge of the screen. The new screen is pressed into place, and the finder put back on.
There are two different motorized film advance units in the New F-1 system: the AE Power Winder FN, and the AE Motor Drive FN. The AE Power Winder FN allows up to 2 frames per second (frame/s) in continuous mode, and the AE Motor Drive allows up to 5 frame/s in high-speed mode and 3.5 frame/s in low-speed mode. Both units also have single-exposure mode, where only a single frame is exposed when the shutter release is held down. Both units also have a second shutter release for vertical format shooting, and a subtractive frame counter. Only the AE Motor Drive FN has a motorized film rewind (therefore when using the AE Power Winder FN it is not necessary to remove the Rewind Coupler cover from the bottom of the camera).
The AE Power Winder FN is powered by 4 AA batteries, and is a single self-contained, unexpandable unit. The AE Motor Drive FN is a more complete system, as it has 3 different battery packs to choose from: the Battery Pack FN, the Ni-Cd Pack FN, and the High Power Ni-Cd Pack FN. The Battery and High Power Ni-Cd packs will power the motor drive for up to 50 rolls of film, while the Ni-Cd pack provides power for up to 30 rolls. The Battery Pack FN takes 12 AA batteries. The two Ni-Cd packs have to be plugged into a charger to recharge them. The High Power Ni-Cd pack will also power the camera body itself by replacing the camera's battery with Battery Cord C-FN.
Both units add the possibility of shutter-priority auto exposure mode by setting the lens's aperture ring to 'A'. The aperture needle disappears from the meter display, and the meter needle indicates what aperture the AE system has selected. Also, using either of the motor drive systems also enables use of electronic interval timers and remote shutter releases, both wired and wireless.
The standard camera back is also interchangeable with a couple other units. One is the Data Back FN, which has 3 dials with letters, numbers, and Roman numerals. The left-hand dial is labeled "Year", and has a blank, 0-9, 82-93, I-X, and a-g; the middle dial is labeled "Month", and has a blank, 0-31, and A-G; the right-hand dial is labeled "Day", and has a blank, and 0-31. The back imprints the dial settings onto the film for classification or dating purposes, either at the time of shutter release, or when the manual record button is pressed.
The Film Chamber FN-100 is a bulk film back which allows up to 100 exposures without reloading. It requires use of the AE Motor Drive FN.
In addition to the standard version of the New F-1, Canon produced a few special editions of the camera.
1983 Canon launched a commemorative model for its 50th anniversary. The model is a standard model with a golden Canon logo.
Canon delivered a few models for the Swiss Post with a fixed ALOS 35mm f/3.5 lens.
Canon was the official camera sponsor of the 1984 Summer Olympics and produced a commemorative edition of the New F-1 for the occasion.[2] This edition has gold instead of white for the 'Canon' and 'F-1' lettering on the camera, and a gold 1984 Summer Olympics emblem on the rewind side of the front. Both the AE Finder FN and Eye Level Finder FN were available. The Eye-level Finder FN Olympic editions are much more difficult to find now, presumably due to lower production compared to the AE Finder version.
Also constructed for the 1984 Summer Olympics was a high-speed camera for the sports photographers covering the event.[3] This followed on from Canon's previous attempt at a high-speed sports photography camera, the F-1 High Speed Motor Drive camera, produced for the 1972 Winter Olympics held in Sapporo, Japan. This new camera attained a record 14 frames per second performance, achieved through the use of a fixed pellicle mirror instead of the normal moving mirror, a high-speed metal blade shutter, and a large and powerful motor unit and battery pack. It is estimated that under a hundred of these specialised cameras were constructed.
Canon supplied a number of New F-1 cameras to the U.S. Navy. These were largely identical to the civilian models except for Navy markings.